This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Width 35 3/4Open original source ↗ Why this value was usedWidth 35 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69.125 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Height to Top of Case 69 1/8Open original source ↗ Why this value was usedHeight to Top of Case 69 1/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70.25 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Height to Top of Hinge 70 1/4Open original source ↗ Why this value was usedHeight to Top of Hinge 70 1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 31 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit31 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Depth without Door 31Open original source ↗ Why this value was usedDepth without Door 31 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 35.75 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Depth without Handles 35 3/4Open original source ↗ Why this value was usedDepth without Handles 35 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 38.125 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit38.125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Depth with Handles 38 1/8Open original source ↗ Why this value was usedDepth with Handles 38 1/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 50.125 in | ✓ Conflicting sources — resolved | LG installation document — 90111200.pdf assets.skulytics.io | Retained specification excerpt: Official exact-model sheet: Depth (Total with Door Open 90 degrees) = 50 1/8 in; 38 1/8 in is depth | |
Value used by ExactFit50.125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Official exact-model sheet: Depth (Total with Door Open 90 degrees) = 50 1/8 in; 38 1/8 in is depth with handles.Open original source ↗ Why this value was usedOfficial exact-model sheet: Depth (Total with Door Open 90 degrees) = 50 1/8 in; 38 1/8 in is depth with handles. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 90111200.pdf + 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.75 + 2 * 0.125 Confidence label: medium. Primary evidenceLG measurement source — 90111200.pdf + 90111200.pdf Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.75 + 2 * 0.125 = 36.0 in. Side evidence: Installation Clearance Sides 1/8Open original source ↗ Why this value was usedMinimum opening derived from exact product width plus explicit symmetric side spacing: 35.75 + 2 * 0.125 = 36.0 in. Side evidence: Installation Clearance Sides 1/8 Calculation or inference: 35.75 + 2 * 0.125. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.25 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceLG measurement source — 90111200.pdf Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 33 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 90111198.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceLG measurement source — 90111198.pdf Minimum opening depth derived from case-only depth 31.0 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 31.0 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | LG measurement source — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 90111200.pdf Installation Clearance Sides 1/8Open original source ↗ Why this value was usedInstallation Clearance Sides 1/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | LG measurement source — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 90111200.pdf Installation Clearance Sides 1/8Open original source ↗ Why this value was usedInstallation Clearance Sides 1/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | LG measurement source — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceLG measurement source — 90111200.pdf Installation Clearance | Sides 1/8", Top 1", Back 2" | Weight (Unit/Carton)Open original source ↗ Why this value was usedInstallation Clearance | Sides 1/8", Top 1", Back 2" | Weight (Unit/Carton) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | LG measurement source — 90111198.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 90111198.pdf Back Clearance 2"Open original source ↗ Why this value was usedBack Clearance 2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.63 in | ✓ Verified — retained secondary source | LG measurement source — popular_lg_cached_hinge_evidence.json web.archive.org | Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model | |
Value used by ExactFit4.63 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceLG measurement source — popular_lg_cached_hinge_evidence.json Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model official specification: Door Edge Clearance with Handle 4.63".Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model official specification: Door Edge Clearance with Handle 4.63". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | LG installation document — 90111200.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 90111200.pdf Width 35 3/4Open original source ↗ Why this value was usedWidth 35 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 50.125 in. Earlier retained values: 38.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official exact-model sheet: Depth (Total with Door Open 90 degrees) = 50 1/8 in; 38 1/8 in is depth with handles.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: LRMXS3006S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: LRMXS3006S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: LRMXS3006S. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗web.archive.org · Web source · secondary model/source
Model numbers covered: LRMXS3006S. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.