Measurement evidence for LG LRMDC2306S

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306_%20Spec%20Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width 35 3/4 in
Reviewed: 2026-09-04

Width 35 3/4 in

Why this value was used

Width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Case: 69.0 in | out Handles 28 7/8" Depth without Door 24" Depth (Total with Door O
Reviewed: 2026-09-04

Height to Top of Case: 69.0 in | out Handles 28 7/8" Depth without Door 24" Depth (Total with Door Open) 43 1/4" Height to Top of Case 69" Height to Top of Door Hinge 70 1/4" Width 35 3/4" Width (Door Open 90˚ with Han

Why this value was used

Height to Top of Case: 69.0 in | out Handles 28 7/8" Depth without Door 24" Depth (Total with Door Open) 43 1/4" Height to Top of Case 69" Height to Top of Door Hinge 70 1/4" Width 35 3/4" Width (Door Open 90˚ with Han

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Door Hinge: 70.25 in | without Door 24" Depth (Total with Door Open) 43 1/4" Height
Reviewed: 2026-09-04

Height to Top of Door Hinge: 70.25 in | without Door 24" Depth (Total with Door Open) 43 1/4" Height to Top of Case 69" Height to Top of Door Hinge 70 1/4" Width 35 3/4" Width (Door Open 90˚ with Handle) 45" Width (Door Open 90˚ withou

Why this value was used

Height to Top of Door Hinge: 70.25 in | without Door 24" Depth (Total with Door Open) 43 1/4" Height to Top of Case 69" Height to Top of Door Hinge 70 1/4" Width 35 3/4" Width (Door Open 90˚ with Handle) 45" Width (Door Open 90˚ withou

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306_%20Spec%20Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door 24 1/8 in
Reviewed: 2026-09-04

Depth without Door 24 1/8 in

Why this value was used

Depth without Door 24 1/8 in

Other evidence found

• 24 in — superseded

  media.us.lg.com; location not retained. Model scope: not separately recorded. Raw value: ith Handles 31 1/4" Depth without Handles 28 7/8" Depth without Door 24" Depth (Total with Door Open) 43 1/4" Height to To. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306_%20Spec%20Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Handles 28 7/8 in
Reviewed: 2026-09-04

Depth without Handles 28 7/8 in

Why this value was used

Depth without Handles 28 7/8 in

Other evidence found

• 28.88 in — superseded

  media.us.lg.com; location not retained. Model scope: not separately recorded. Raw value: Depth without Handles: 28.88 in | ] LRMDC2306S - LG Electronics / CLEARANCES / WEIGHTS Depth with Handles 31 1/4" Depth without Handles 28 7/8" Depth without Door 24" Depth (Total with Door Open) 43 1/4" Height to Top of Ca. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Handles: 31.25 in | [PDF] LRMDC2306S - LG Electronics / CLEARANCES / WEIGHTS Depth with H
Reviewed: 2026-09-04

Depth with Handles: 31.25 in | [PDF] LRMDC2306S - LG Electronics / CLEARANCES / WEIGHTS Depth with Handles 31 1/4" Depth without Handles 28 7/8" Depth without Door 24" Depth (Total with Door Ope

Why this value was used

Depth with Handles: 31.25 in | [PDF] LRMDC2306S - LG Electronics / CLEARANCES / WEIGHTS Depth with Handles 31 1/4" Depth without Handles 28 7/8" Depth without Door 24" Depth (Total with Door Ope

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Total with Door Open 90°: 43.25 in | e 31 1/4" (793 mm) H Depth (Total with Freezer Drawer Op
Reviewed: 2026-09-04

Depth (Total with Door Open 90°: 43.25 in | e 31 1/4" (793 mm) H Depth (Total with Freezer Drawer Open) 47 3/4" (1213 mm) I Depth (Total with Door Open 90°) 43 1/4" (1097 mm) B A C D F I H E G B A C D F I H E G LIMITED WARRANTY Parts & Labor 1

Why this value was used

Depth (Total with Door Open 90°: 43.25 in | e 31 1/4" (793 mm) H Depth (Total with Freezer Drawer Open) 47 3/4" (1213 mm) I Depth (Total with Door Open 90°) 43 1/4" (1097 mm) B A C D F I H E G B A C D F I H E G LIMITED WARRANTY Parts & Labor 1

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.0

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

LG measurement source — LRMDC2306_%20Spec%20Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 *
Reviewed: 2026-09-18

Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.0 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.

Why this value was used

Reviewed appliance width plus reviewed per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.0 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged. Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.125 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.125 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Why this value was used

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Why this value was used

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Why this value was used

Installation Clearance | Sides 1/8", Top 1", Back 2" | Approx. Weight (Product / | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — LRMDC2306S-LG-Builder-Spec-Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

C Height to Top of Case 69" (1753 mm) | D Height to Top of Hinge 70 11/44" (1785 mm) | E Back Clearance 2" (50 mm)

Why this value was used

C Height to Top of Case 69" (1753 mm) | D Height to Top of Hinge 70 11/44" (1785 mm) | E Back Clearance 2" (50 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

LG measurement source — popular_lg_cached_hinge_evidence.json
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model specification: Door Edge Clearance with Handle 4 5/8".

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model specification: Door Edge Clearance with Handle 4 5/8".

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

LG measurement source — LRMDC2306_%20Spec%20Sheet.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacture
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.