This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-09. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Measurements and supporting evidence
Measurement
Value used
Evidence status
Primary source
Location
Details
Overall width
35.75 in
? Verified — finalized database measurement
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
35.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
68.875 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
70.25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
24.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
29.125 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 14
Value used by ExactFit
31.625 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 14 Reviewed: 2026-09-09
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 14
Value used by ExactFit
43.625 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 14 Reviewed: 2026-09-09
LRFLC2726*: Depth Total with Door Open 90 degrees 43 5/8 in
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
{"calculation": "70.25 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "LRFLC2726*: Height to Top of Hinge 70 1/4 in", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 70.25}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LRFLC2706S/90111138.pdf", "page": 2, "raw": "Height to Top of Door Hinge\n70 1/4\"", "source_url": "https://assets.skulytics.io/assets/docs/LRFLC2706S-90111138.pdf", "value_in": 70.25}], "top_clearance_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 1, "raw": "Top 1 in", "source_url": "https://www.lg.com/us/support/products/documents/LRFLC2726S_2026_Spec_Sheet_REF.pdf", "value_in": 1.0}]}, "result_in": 71.25}
{"calculation": "70.25 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "LRFLC2726*: Height to Top of Hinge 70 1/4 in", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 70.25}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LRFLC2706S/90111138.pdf", "page": 2, "raw": "Height to Top of Door Hinge\n70 1/4\"", "source_url": "https://assets.skulytics.io/assets/docs/LRFLC2706S-90111138.pdf", "value_in": 70.25}], "top_clearance_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 1, "raw": "Top 1 in", "source_url": "https://www.lg.com/us/support/products/documents/LRFLC2726S_2026_Spec_Sheet_REF.pdf", "value_in": 1.0}]}, "result_in": 71.25} Calculation or inference: 70.25 + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "LRFLC2726*: Depth without Door 24 3/4 in", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 24.75}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LRFLC2706S/90111138.pdf", "page": 2, "raw": "Depth without Door\n24 3/4\"", "source_url": "https://assets.skulytics.io/assets/docs/LRFLC2706S-90111138.pdf", "value_in": 24.75}], "rear_clearance_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "Allow at least 2 inches between the back of the refrigerator and the wall", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 2.0}]}, "result_in": 26.75}
{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "LRFLC2726*: Depth without Door 24 3/4 in", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 24.75}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LRFLC2706S/90111138.pdf", "page": 2, "raw": "Depth without Door\n24 3/4\"", "source_url": "https://assets.skulytics.io/assets/docs/LRFLC2706S-90111138.pdf", "value_in": 24.75}], "rear_clearance_in": [{"cache_path": "data/truth-set/lg-lrflc2726s.json", "page": 13, "raw": "Allow at least 2 inches between the back of the refrigerator and the wall", "source_url": "https://www.canadianappliance.ca/pdf/lg/refrigerator/LF32BSH42S_user-manual.pdf", "value_in": 2.0}]}, "result_in": 26.75} Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
LG measurement source — lg-lrflc2726s.json www.canadianappliance.ca
Page 13
Value used by ExactFit
2 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json www.canadianappliance.ca · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
Allow at least 2 inches between the back of the refrigerator and the wall
Allow at least 2 inches between the back of the refrigerator and the wall
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
LG measurement source — lg-lrflc2726s.json assets.skulytics.io
Page 13
Value used by ExactFit
35.75 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
LG measurement source — lg-lrflc2726s.json LG · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
