Measurement evidence for LG LHTNS2403S

Value used by ExactFit

33 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width 33”
Reviewed: 2026-09-09

Width 33”

Why this value was used

Width 33”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Case 68”
Reviewed: 2026-09-09

Height to Top of Case 68”

Why this value was used

Height to Top of Case 68”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Hinge 69”
Reviewed: 2026-09-09

Height to Top of Hinge 69”

Why this value was used

Height to Top of Hinge 69”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door 29.5”
Reviewed: 2026-09-09

Depth without Door 29.5”

Why this value was used

Depth without Door 29.5”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Handles 34”
Reviewed: 2026-09-09

Depth without Handles 34”

Why this value was used

Depth without Handles 34”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Handles 34”
Reviewed: 2026-09-09

Depth with Handles 34”

Why this value was used

Depth with Handles 34”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

63 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Total with Door Open 90°) 63”
Reviewed: 2026-09-09

Depth (Total with Door Open 90°) 63”

Why this value was used

Depth (Total with Door Open 90°) 63”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

37 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_vent
Reviewed: 2026-09-09

{"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_ventilation_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}], "width_doors_closed_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Width 33”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 33.0}]}, "result_in": 37.0}

Why this value was used

{"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_ventilation_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}], "width_doors_closed_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Width 33”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 33.0}]}, "result_in": 37.0} Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 69.0 + top_clearance_in

Confidence label: high.

Calculation inputs: Top clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "69.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sou
Reviewed: 2026-09-09

{"calculation": "69.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Height to Top of Hinge 69”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 69.0}], "top_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}]}, "result_in": 71.0}

Why this value was used

{"calculation": "69.0 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Height to Top of Hinge 69”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 69.0}], "top_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}]}, "result_in": 71.0} Calculation or inference: 69.0 + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cach
Reviewed: 2026-09-09

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Depth without Door 29.5”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 29.5}], "rear_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}]}, "result_in": 31.5}

Why this value was used

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Depth without Door 29.5”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 29.5}], "rear_clearance_in": [{"cache_path": "data/sources/LG/LHTNS2403S/spec-sheet-lg-usa-2022-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS table", "raw": "Installation Clearance Sides 2”, Top 2”, Back 2”", "source_url": "https://www.lg.com/us/refrigerators/lg-lhtns2403s-top-freezer-refrigerator", "value_in": 2.0}]}, "result_in": 31.5} Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 2”, Top 2”, Back 2”
Reviewed: 2026-09-09

Installation Clearance Sides 2”, Top 2”, Back 2”

Why this value was used

Installation Clearance Sides 2”, Top 2”, Back 2”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 2”, Top 2”, Back 2”
Reviewed: 2026-09-09

Installation Clearance Sides 2”, Top 2”, Back 2”

Why this value was used

Installation Clearance Sides 2”, Top 2”, Back 2”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 2”, Top 2”, Back 2”
Reviewed: 2026-09-09

Installation Clearance Sides 2”, Top 2”, Back 2”

Why this value was used

Installation Clearance Sides 2”, Top 2”, Back 2”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 2”, Top 2”, Back 2”
Reviewed: 2026-09-09

Installation Clearance Sides 2”, Top 2”, Back 2”

Why this value was used

Installation Clearance Sides 2”, Top 2”, Back 2”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lg-lhtns2403s-top-freezer-refrigerator
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Manufacturer page/document for Exact model LHTNS2403S product page: Door Edge Clearance with Handle — 2"; Door Edge Clearance without Handle — 2". LG door edge clearance with handle (LG rule: use the with-handle figure). Door angle not stated on the label; the same table prints 90-degree widths. Found 2026-10-25.

Why this value was used

Manufacturer page/document for Exact model LHTNS2403S product page: Door Edge Clearance with Handle — 2"; Door Edge Clearance without Handle — 2". LG door edge clearance with handle (LG rule: use the with-handle figure). Door angle not stated on the label; the same table prints 90-degree widths. Found 2026-10-25.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-2022-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width 33”
Reviewed: 2026-09-09

Width 33”

Why this value was used

Width 33”

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.