Measurement evidence for LG LF29S8230V

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Exact-model LG Home Solutions specification sheet, page 1: Width = 35 3/4 in

Why this value was used

Exact-model LG Home Solutions specification sheet, page 1: Width = 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — Specification%2BSheet
files.bbystatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to Top of Case = 68 7/8" | Height to Top of Case | 68 7/8" | Height (Floor to Top of

Why this value was used

Height to Top of Case = 68 7/8" | Height to Top of Case | 68 7/8" | Height (Floor to Top of

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — frlkkjwzdmlf.pdf
images.webfronts.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Hinge = 70.25 in | " (874 mm) B Width 35 3/4" (908 mm) C Height to Top of Case 68 7
Reviewed: 2026-09-04

Height to Top of Hinge = 70.25 in | " (874 mm) B Width 35 3/4" (908 mm) C Height to Top of Case 68 7/8" (1750 mm) D Height to Top of Hinge 70 1/4" (1785 mm) E Back Clearance 2" (50 mm) F Depth without Door 30 1/8" (764mm) G De

Why this value was used

Height to Top of Hinge = 70.25 in | " (874 mm) B Width 35 3/4" (908 mm) C Height to Top of Case 68 7/8" (1750 mm) D Height to Top of Hinge 70 1/4" (1785 mm) E Back Clearance 2" (50 mm) F Depth without Door 30 1/8" (764mm) G De

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — Specification%2BSheet
files.bbystatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth without Door = 30 1/8" | Depth without Door | 30 1/8" | Depth without Handles

Why this value was used

Depth without Door = 30 1/8" | Depth without Door | 30 1/8" | Depth without Handles

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — Specification%2BSheet
files.bbystatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth without Handles = 34 3/8" | Depth without Handles | 34 3/8" | Depth (to Hinge Cover)

Why this value was used

Depth without Handles = 34 3/8" | Depth without Handles | 34 3/8" | Depth (to Hinge Cover)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from LF29S8365S

Confidence label: medium.

Primary evidence

LG measurement source — 90110955.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Medium-confidence chassis inference from LF29S8365S. Donors unanimously report depth_with_handles_in=34.375 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in. Donor evidence: WxHxD) 35 3/4" x 70 1/4" x 34 3/8"

Why this value was used

Medium-confidence chassis inference from LF29S8365S. Donors unanimously report depth_with_handles_in=34.375 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in. Donor evidence: WxHxD) 35 3/4" x 70 1/4" x 34 3/8" Calculation or inference: same-brand product-class chassis propagation from LF29S8365S.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — frlkkjwzdmlf.pdf
images.webfronts.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Total with Door Open 90° = 48.875 in | th with Handle N/A H Depth (Total with Freezer Drawer
Reviewed: 2026-09-04

Depth (Total with Door Open 90° = 48.875 in | th with Handle N/A H Depth (Total with Freezer Drawer Open) 55 3/8" (1406 mm) I Depth (Total with Door Open 90°) 48 7/8" (1240mm) DIMENSION / CLEARANCES • Check the dimensions of the appliance and the

Why this value was used

Depth (Total with Door Open 90° = 48.875 in | th with Handle N/A H Depth (Total with Freezer Drawer Open) 55 3/8" (1406 mm) I Depth (Total with Door Open 90°) 48 7/8" (1240mm) DIMENSION / CLEARANCES • Check the dimensions of the appliance and the

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.125

Confidence label: medium.

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf + 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on each side.

Why this value was used

Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.125.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top c
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — frlkkjwzdmlf.pdf
images.webfronts.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 30.125 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 30.125 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 30.125 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Why this value was used

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Why this value was used

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Why this value was used

Installation Clearance Sides = 0.125 in | (Total with Door Open) 48 1/2" Depth (Draw Open Fully with­ out Handle) 55 3/8" Installation Clearance Sides 1/8", Top 1", Back 2" Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 36 3/8" Weight ( | cached support: images.thdstatic.com, images.webfronts.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — frlkkjwzdmlf.pdf
images.webfronts.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Back Clearance 2"
Reviewed: 2026-09-05

Back Clearance 2"

Why this value was used

Back Clearance 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

LG measurement source — 0cbe2c55-6ba5-4057-8304-550f20176f9c.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.