This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf Width 35 3/4"Open original source ↗ Why this value was usedWidth 35 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69 in | ✓ Conflicting sources — resolved | LG measurement source — lg-lf29h8330s-french-4-door-refrigerator LG | Retained specification excerpt: Reviewed cached exact-model manufacturer label: Height to Top of Case = 69.0 in. Context: Door Edge | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — lg-lf29h8330s-french-4-door-refrigerator Reviewed cached exact-model manufacturer label: Height to Top of Case = 69.0 in. Context: Door Edge Clearance with Handle 4.25" Door Edge Clearance without Handle 2.25" Height to Top of Case 69" Height to Top of Door Hinge 70.37" Installation Clearance Sides 1/8", Top 1", BOpen original source ↗ Why this value was usedReviewed cached exact-model manufacturer label: Height to Top of Case = 69.0 in. Context: Door Edge Clearance with Handle 4.25" Door Edge Clearance without Handle 2.25" Height to Top of Case 69" Height to Top of Door Hinge 70.37" Installation Clearance Sides 1/8", Top 1", B Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70.375 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf W x H x D) 35 3/4" x 70 3/8" x 34 3/8"Open original source ↗ Why this value was usedW x H x D) 35 3/4" x 70 3/8" x 34 3/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 30 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf Depth without Door 30"Open original source ↗ Why this value was usedDepth without Door 30" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.375 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf Depth without Handles 34 3/8Open original source ↗ Why this value was usedDepth without Handles 34 3/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36.875 in | ✓ Conflicting sources — resolved | LG measurement source — 77836537.pdf LG | Page 1 | |
Value used by ExactFit36.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 77836537.pdf LG spec sheet LF29H8330_ (8/7/23), Dimensions: Depth (with Handles) 36 7/8". Replaces the rounded web figure 36.87/36.873 in.Open original source ↗ Why this value was usedLG spec sheet LF29H8330_ (8/7/23), Dimensions: Depth (with Handles) 36 7/8". Replaces the rounded web figure 36.87/36.873 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.5 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit48.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf Depth (Total with Door Open) 48 1/2Open original source ↗ Why this value was usedDepth (Total with Door Open) 48 1/2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf LG | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * exact-model installation side clearance Confidence label: medium. Calculation inputs: Overall width; Primary evidenceLG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf Derived minimum opening width: 35.75 + 2 x 0.125 = 36 in. Exact-model clearance evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8"Open original source ↗ All retained supporting links
Why this value was usedDerived minimum opening width: 35.75 + 2 x 0.125 = 36 in. Exact-model clearance evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8" Calculation or inference: width_doors_closed_in + 2 * exact-model installation side clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.375 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceLG measurement source — 77836537.pdf Minimum opening height derived from highest stored appliance endpoint 70.375 in plus documented top clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 70.375 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 32 in | ✓ Verified — retained secondary source · Calculated/inferred | LG measurement source — 77836537.pdf device.report | Page 1 | |
Value used by ExactFit32 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceLG measurement source — 77836537.pdf LG spec sheet LF29H8330_: Depth without Door 30" plus Installation Clearance Back 2" = 32 in, as for LF29H8330D. Replaces 38 7/8 in from a third-party listing (device.report).Open original source ↗ Why this value was usedLG spec sheet LF29H8330_: Depth without Door 30" plus Installation Clearance Back 2" = 32 in, as for LF29H8330D. Replaces 38 7/8 in from a third-party listing (device.report). Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | LG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf LG | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8"Open original source ↗ All retained supporting links
Why this value was usedCorrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | LG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf LG | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG measurement source — 77836537.pdf + lg-lf29h8330s-french-4-door-refrigerator + LF29H8330_spec_sheet.pdf Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8"Open original source ↗ All retained supporting links
Why this value was usedCorrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance Sides 1/8"; Installation Clearance Sides 1/8"; Installation Clearance | Sides 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | LG measurement source — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceLG measurement source — 77836537.pdf Installation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD)Open original source ↗ Why this value was usedInstallation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | LG specification record — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG specification record — 77836537.pdf Installation Clearance Sides 1/8", Top 1", Back 2"Open original source ↗ Why this value was usedInstallation Clearance Sides 1/8", Top 1", Back 2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.25 in | ✓ Verified — retained secondary source | LG measurement source — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit4.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceLG measurement source — 77836537.pdf Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/4"Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | LG installation document — 77836537.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceLG installation document — 77836537.pdf Width 35 3/4"Open original source ↗ Why this value was usedWidth 35 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69 in. Earlier retained values: 70.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Height to Top of Case = 69.0 in. Context: Door Edge Clearance with Handle 4.25" Door Edge Clearance without Handle 2.25" Height to Top of Case 69" Height to Top of Door Hinge 70.37" Installation Clearance Sides 1/8", Top 1", B
View source scope, location, and impact on fitSelected: 36.875 in. Earlier retained values: 34.375 in, 36.873 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
LG spec sheet LF29H8330_ (8/7/23), Dimensions: Depth (with Handles) 36 7/8". Replaces the rounded web figure 36.87/36.873 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: LF29H8330S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗LG · Web source · exact model/source
Model numbers covered: LF29H8330S. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Cabinet height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗LG · Web source · exact model/source
Model numbers covered: LF29H8330S. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
3 displayed measurements supported: Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.