Measurement evidence for LG LF26C8210S

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-24

Width 35 3/4" is the only width the sheet prints for the appliance; no separate closed-door width is given. The stored 37 7/8" was the carton width.

Why this value was used

Width 35 3/4" is the only width the sheet prints for the appliance; no separate closed-door width is given. The stored 37 7/8" was the carton width.

Other evidence found

• 37.875 in — superseded

  Document 104687246.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG installation document — 104687246.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to Top of Case 68 7/8

Why this value was used

Height to Top of Case 68 7/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lf26c8210s
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Height to Top of Hinge = 70.25 in. Context: ch) 29 3
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Height to Top of Hinge = 70.25 in. Context: ch) 29 3/4" - Gross Weight (lb.) 291.0 - Height to Top of Case (inch) 68 7/8" - Height to Top of Hinge or Door Cap Deco (inch) 70 1/4" - Installation Clearance Back 2" - Packing Dimension (WxHxD, inch) 37 7/8" x 72

Why this value was used

Reviewed cached exact-model manufacturer label: Height to Top of Hinge = 70.25 in. Context: ch) 29 3/4" - Gross Weight (lb.) 291.0 - Height to Top of Case (inch) 68 7/8" - Height to Top of Hinge or Door Cap Deco (inch) 70 1/4" - Installation Clearance Back 2" - Packing Dimension (WxHxD, inch) 37 7/8" x 72

Other evidence found

• 72.375 in — superseded

  Document 104687246.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG installation document — 104687246.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth without Door 25 3/8"

Why this value was used

Depth without Door 25 3/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG installation document — 104687246.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth without Handles 29 3/4"

Why this value was used

Depth without Handles 29 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-24

Depth (with Handles) 32 1/4"; the sheet prints Depth without Handles 29 3/4" separately. The stored 29 3/4" came from a web page and was the without-handles value.

Why this value was used

Depth (with Handles) 32 1/4"; the sheet prints Depth without Handles 29 3/4" separately. The stored 29 3/4" came from a web page and was the without-handles value.

Other evidence found

• 35.125 in — superseded

  Document 104687246.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8". The final reviewed registry supersedes this earlier audit value.

• 29.75 in — superseded

  www.lg.com; location not retained. Model scope: not separately recorded. Raw value: Official exact-model product depth is 29.75 in; prior 35.125 in was carton depth from the WxHxD carton row.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

42.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG installation document — 104687246.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth (Total with Door Open) 42 1/2"

Why this value was used

Depth (Total with Door Open) 42 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_width_in = case_width_in + 2 * 0.125

Confidence label: high.

Calculation inputs: Cabinet case width;

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-24

Recalculated 2026-09-24 after the width correction: Width 35 3/4" plus Installation Clearance Sides 1/8" on each side = 36 in (previously 38.125 in, derived from the carton width 37 7/8").

Why this value was used

Recalculated 2026-09-24 after the width correction: Width 35 3/4" plus Installation Clearance Sides 1/8" on each side = 36 in (previously 38.125 in, derived from the carton width 37 7/8"). Calculation or inference: min_cutout_width_in = case_width_in + 2 * 0.125.

Other evidence found

• 38.125 in — superseded

  Document 104687246.pdf; page 1. Model scope: not separately recorded. Raw value: Derived minimum opening width: 37.875 + 2 x 0.125 = 38.125 in. Exact-model clearance evidence: Installation Clearance | Sides 1/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — LF26C8210S_104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-07

Exact sheet: Depth without Door 25 3/8" plus Installation Clearance Back 2" = 27 3/8".

Why this value was used

Exact sheet: Depth without Door 25 3/8" plus Installation Clearance Back 2" = 27 3/8". Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance | Sides 1/8"

Why this value was used

Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance | Sides 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance | Sides 1/8"

Why this value was used

Corrected prior semantic mismatch 4.25 in (Door Edge Clearance with Handle 4 1/4"). Exact-model installation-side evidence: Installation Clearance | Sides 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Installation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD)

Why this value was used

Installation Clearance | Sides 1/8", Top 1", Back 2" | Carton Dimensions (WxHxD)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG specification record — 104687246.pdf
assets.skulytics.io · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/4"

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Door Edge Clearance with Handle 4 1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 104687246.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-24

Width 35 3/4"; Total (WxHxD) 35 3/4" x 70 1/4" x 32 1/4". The stored 37 7/8" was the Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8" line, which is the shipping box, not the appliance.

Why this value was used

Width 35 3/4"; Total (WxHxD) 35 3/4" x 70 1/4" x 32 1/4". The stored 37 7/8" was the Carton Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8" line, which is the shipping box, not the appliance.

Other evidence found

• 37.875 in — superseded

  Document 104687246.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 37 7/8" x 72 3/8" x 35 1/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.