Measurement evidence for LG LF26C6230V

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Exact-model LG Home Solutions specification sheet, page 1: Width = 35 3/4 in

Why this value was used

Exact-model LG Home Solutions specification sheet, page 1: Width = 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Height to Top of Case = 68 7/8" | Height to Top of Case | 68 7/8" (1750 mm) | D

Why this value was used

Height to Top of Case = 68 7/8" | Height to Top of Case | 68 7/8" (1750 mm) | D

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Height to Top of Hinge = 70 1/4" | Height to Top of Hinge | 70 1/4" (1785 mm) | E

Why this value was used

Height to Top of Hinge = 70 1/4" | Height to Top of Hinge | 70 1/4" (1785 mm) | E

Other evidence found

• 2 in — superseded

  www.notice-facile.com; location not retained. Model scope: not separately recorded. Raw value: d height to top of hinge 70 1/4" (1785 mm) 70 1/4" (1785 mm) : E Back Clearance 2" (50 mm) 2" (50 mm) . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth without Door = 24 3/4" | Depth without Door | 24 3/4" (628mm) | G

Why this value was used

Depth without Door = 24 3/4" | Depth without Door | 24 3/4" (628mm) | G

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth without Handle = 29 1/8" | Depth without Handle | 29 1/8" (739 mm) | B

Why this value was used

Depth without Handle = 29 1/8" | Depth without Handle | 29 1/8" (739 mm) | B

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth with Handle = 31 5/8" | Depth with Handle | 31 5/8" (802mm) | H

Why this value was used

Depth with Handle = 31 5/8" | Depth with Handle | 31 5/8" (802mm) | H

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Total with Door Open 90° = 43.625 in | le 31 5/8" (802mm) H Depth (Total with Freezer Drawer
Reviewed: 2026-09-04

Depth (Total with Door Open 90° = 43.625 in | le 31 5/8" (802mm) H Depth (Total with Freezer Drawer Open) 48 7/8" (1239 mm) I Depth (Total with Door Open 90°) 43 5/8" (1106mm) DIMENSION / CLEARANCES • Check the dimensions of the appliance and the

Why this value was used

Depth (Total with Door Open 90° = 43.625 in | le 31 5/8" (802mm) H Depth (Total with Freezer Drawer Open) 48 7/8" (1239 mm) I Depth (Total with Door Open 90°) 43 5/8" (1106mm) DIMENSION / CLEARANCES • Check the dimensions of the appliance and the

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.125

Confidence label: medium.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf + 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on each side.

Why this value was used

Derived minimum opening width 36.0 in from product width 35.75 in and explicit 0.125 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.125.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

LG measurement source — lg-lf26c6230v-french-3-door-refrigerator
LG · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top c
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.25 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.75 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.75 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.75 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lg-lf26c6230v-french-3-door-refrigerator
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height t
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Why this value was used

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lg-lf26c6230v-french-3-door-refrigerator
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height t
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Why this value was used

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lg-lf26c6230v-french-3-door-refrigerator
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height t
Reviewed: 2026-09-05

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Why this value was used

Installation Clearance Sides = 0.125 in | 29.125" Door Edge Clearance without Handle 2.25" Height to Top of Case 68.875" Installation Clearance Sides 1/8", Top 1", Back 2" Weight (Unit/Carton) 262 lbs / 284 lbs Width 35.75" Width (Doo

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Back Clearance | 2" (50 mm) | F
Reviewed: 2026-09-05

Back Clearance | 2" (50 mm) | F

Why this value was used

Back Clearance | 2" (50 mm) | F

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — lg-lf26c6230v-french-3-door-refrigerator
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

LG product page: "Door Edge Clearance without Handle — 2.25"" (door angle not stated on the label). The LG owner's manual lists this model under 'Models without handles' (LF26C6230V/02_PDF_REF_NA0_MFL69497046_12_260608_00_OM_WEB_EN.pdf (owner's manual MFL69497046, Installation: 'Models without handles ... LF26C6230*')), so the without-handle figure is the door's full clearance. Owner decision 2026-10-25.

Why this value was used

LG product page: "Door Edge Clearance without Handle — 2.25"" (door angle not stated on the label). The LG owner's manual lists this model under 'Models without handles' (LF26C6230V/02_PDF_REF_NA0_MFL69497046_12_260608_00_OM_WEB_EN.pdf (owner's manual MFL69497046, Installation: 'Models without handles ... LF26C6230*')), so the without-handle figure is the door's full clearance. Owner decision 2026-10-25.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

LG measurement source — 12d4479e-9c87-4880-aa90-ba63616a5c10.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.