Measurement evidence for LG LF25H6200S

Value used by ExactFit

32.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width 32 15/16"
Reviewed: 2026-09-09

Width 32 15/16"

Why this value was used

Width 32 15/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Case 68 5/8''
Reviewed: 2026-09-09

Height to Top of Case 68 5/8''

Why this value was used

Height to Top of Case 68 5/8''

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height (Top of Hinge or Door cap Décor) 69 15/16"
Reviewed: 2026-09-09

Height (Top of Hinge or Door cap Décor) 69 15/16"

Why this value was used

Height (Top of Hinge or Door cap Décor) 69 15/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door 29 1/2"
Reviewed: 2026-09-09

Depth without Door 29 1/2"

Why this value was used

Depth without Door 29 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.4375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Handles 33 7/16"
Reviewed: 2026-09-09

Depth without Handles 33 7/16"

Why this value was used

Depth without Handles 33 7/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.9375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (with Handles) 35 15/16"
Reviewed: 2026-09-09

Depth (with Handles) 35 15/16"

Why this value was used

Depth (with Handles) 35 15/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

46.6875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Total with Door Open) 46 11/16"
Reviewed: 2026-09-09

Depth (Total with Door Open) 46 11/16"

Why this value was used

Depth (Total with Door Open) 46 11/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_vent
Reviewed: 2026-09-09

{"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_ventilation_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 0.125}], "width_doors_closed_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS", "raw": "Width 32 15/16\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 32.9375}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row B", "raw": "B Width 32 15/16\" (836 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 32.9375}]}, "result_in": 33.1875}

Why this value was used

{"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_ventilation_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 0.125}], "width_doors_closed_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS", "raw": "Width 32 15/16\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 32.9375}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row B", "raw": "B Width 32 15/16\" (836 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 32.9375}]}, "result_in": 33.1875} Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 69.9375 + top_clearance_in

Confidence label: high.

Calculation inputs: Top clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "69.9375 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/
Reviewed: 2026-09-09

{"calculation": "69.9375 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS", "raw": "Height (Top of Hinge or Door cap Décor) 69 15/16\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 69.9375}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row D", "raw": "D Height to Top of Hinge 69 15/16\" (1776 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 69.9375}], "top_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 1.0}]}, "result_in": 70.9375}

Why this value was used

{"calculation": "69.9375 + top_clearance_in", "operands": {"height_hinge_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, DIMENSIONS/CLEARANCES/WEIGHTS", "raw": "Height (Top of Hinge or Door cap Décor) 69 15/16\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 69.9375}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row D", "raw": "D Height to Top of Hinge 69 15/16\" (1776 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 69.9375}], "top_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 1.0}]}, "result_in": 70.9375} Calculation or inference: 69.9375 + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cach
Reviewed: 2026-09-09

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Depth without Door 29 1/2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 29.5}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row F", "raw": "F Depth without Door 29 1/2\" (748 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 29.5}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LF25H6330S/104687244.pdf", "page": 2, "raw": "Depth without Door\n29 1/2\"", "source_url": "https://assets.skulytics.io/assets/docs/LF25H6330S_104687244.pdf", "value_in": 29.5}], "rear_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 2.0}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances bullet and row E", "raw": "Allow at least 2 inches (50.8 mm) between the back of the refrigerator and the wall. E Back Clearance 2\" (51 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 2.0}, {"cache_path": "D:/active-residential-refrigerators-1000-20260817/documents/LG/LF25H6330S/104687244.pdf", "page": 2, "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://assets.skulytics.io/assets/docs/LF25H6330S_104687244.pdf", "value_in": 2.0}]}, "result_in": 31.5}

Why this value was used

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Depth without Door 29 1/2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 29.5}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances, LF25H6330*/LF25H6000*/LF25H6200* column, row F", "raw": "F Depth without Door 29 1/2\" (748 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 29.5}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/LG/LF25H6330S/104687244.pdf", "page": 2, "raw": "Depth without Door\n29 1/2\"", "source_url": "https://assets.skulytics.io/assets/docs/LF25H6330S_104687244.pdf", "value_in": 29.5}], "rear_clearance_in": [{"cache_path": "data/sources/LG/LF25H6200S/spec-sheet-lg-usa-mirror.pdf", "page": "PDF page 1, product-feature dimensions", "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://www.lg.com/us/support/products/documents/LF25H6200S_Refrigeration_Spec_Sheet.pdf", "value_in": 2.0}, {"cache_path": "data/sources/LG/LF25H6200S/owner-manual-mfl67227329-rev09-mirror.pdf", "page": "PDF page 11, Dimensions and Clearances bullet and row E", "raw": "Allow at least 2 inches (50.8 mm) between the back of the refrigerator and the wall. E Back Clearance 2\" (51 mm)", "source_url": "https://www.lg.com/us/support/product/lg-LF25H6200S.ASTCNA0?tab=2", "value_in": 2.0}, {"cache_path": "D:/active-residential-refrigerators-1000-20260817/documents/LG/LF25H6330S/104687244.pdf", "page": 2, "raw": "Installation Clearance Sides 1/8\", Top 1\", Back 2\"", "source_url": "https://assets.skulytics.io/assets/docs/LF25H6330S_104687244.pdf", "value_in": 2.0}]}, "result_in": 31.5} Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.9375 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width 32 15/16"
Reviewed: 2026-09-09

Width 32 15/16"

Why this value was used

Width 32 15/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

LG measurement source — spec-sheet-lg-usa-mirror.pdf
LG · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installation Clearance Sides 1/8", Top 1", Back 2"
Reviewed: 2026-09-09

Installation Clearance Sides 1/8", Top 1", Back 2"

Why this value was used

Installation Clearance Sides 1/8", Top 1", Back 2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.