This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-31. 8 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: Plain exact-model specification row: Width = 35.9375 in | iances 36 Inch Freestanding French Door Re
Value used by ExactFit
35.9375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
KitchenAid measurement source — kitchenaid-krff436sps.html www.designerappliances.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Plain exact-model specification row: Width = 35.9375 in | iances 36 Inch Freestanding French Door Re Reviewed: 2026-09-04
Plain exact-model specification row: Width = 35.9375 in | iances 36 Inch Freestanding French Door Refrigerator with 30.52 cu. ft. Total Capacity: 30.52 Cu. Ft. Width: 35 15/16" Height: 70 1/16" Depth: 37 7/16" Dimensions
Plain exact-model specification row: Width = 35.9375 in | iances 36 Inch Freestanding French Door Refrigerator with 30.52 cu. ft. Total Capacity: 30.52 Cu. Ft. Width: 35 15/16" Height: 70 1/16" Depth: 37 7/16" Dimensions
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162621.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Rounding normalised 2026-10-22: the stored 70.06 in is the same printed dimension as 70 1/16 in (70.
Value used by ExactFit
70.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: same-chassis variant propagation from KRFF436SJP
Confidence label: high.
Primary evidence
KitchenAid measurement source — p.30-cu.-ft.-french-door-refrigerator-with-exterior-water-and-ice.krff436sjp.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Rounding normalised 2026-10-22: the stored 70.06 in is the same printed dimension as 70 1/16 in (70. Reviewed: 2026-10-22
Rounding normalised 2026-10-22: the stored 70.06 in is the same printed dimension as 70 1/16 in (70.0625); every finish of the KRFF436S family carries the same value to within 0.02 in. Source kept as stored.
Rounding normalised 2026-10-22: the stored 70.06 in is the same printed dimension as 70 1/16 in (70.0625); every finish of the KRFF436S family carries the same value to within 0.02 in. Source kept as stored. Calculation or inference: same-chassis variant propagation from KRFF436SJP.
Other evidence found
70.06 in — superseded
The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Sibling-chassis propagation from KRFF436SJP; model codes have the same numeric skeleton, at least four existing chassis dimensions match, and no structural dimensions conflict. Sibling evidence: Height To Top Of Door Hinge: 70.06 in | 1 cu. ft. Gross Weight 364 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 333 lbs Refrigerator . The final reviewed registry supersedes this earlier audit value.
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162621.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162621.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162621.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Retained specification excerpt: /500 in | | Depth Excluding Doors | 29-7/8 in | | Depth With Door Open 90 Degree | 49 in | | Freezer
Value used by ExactFit
49 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
KitchenAid measurement source — krff436sps slymanbros.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: /500 in | | Depth Excluding Doors | 29-7/8 in | | Depth With Door Open 90 Degree | 49 in | | Freezer Reviewed: 2026-09-04
/500 in | | Depth Excluding Doors | 29-7/8 in | | Depth With Door Open 90 Degree | 49 in | | Freezer Capacity Volume | 9.01 cu. ft. | | Gr
36.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 35.9375 + 2 * 0.5 = 36.9375
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162622.pdf slymanbros.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-10-31
KitchenAid's installation documents for KRFF436SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and 1/2 (1." Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.1875 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).
KitchenAid's installation documents for KRFF436SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and 1/2 (1." Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.1875 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 35.9375 + 2 * 0.5 = 36.9375.
Other evidence found
36.1875 in — superseded
slymanbros.com; location not retained. Model scope: not separately recorded. Raw value: Exact model specification table: Cutout Width 36.188 in; normalized to 36 3/16 in. The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
KitchenAid measurement source — dimension-guide-w11783878-reva.pdf KitchenAid · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-22
Rounding normalised 2026-10-22: the stored 70.56 in is the same printed dimension as 70 9/16 in (70.5625); every finish of the KRFF436S family carries the same value to within 0.02 in. Source kept as stored.
Rounding normalised 2026-10-22: the stored 70.56 in is the same printed dimension as 70 9/16 in (70.5625); every finish of the KRFF436S family carries the same value to within 0.02 in. Source kept as stored. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF436SPS
Confidence label: high.
Primary evidence
KitchenAid measurement source — dimension-guide-w11783878-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern KRFF436SPS.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF436SPS
Confidence label: high.
Primary evidence
KitchenAid measurement source — dimension-guide-w11783878-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern KRFF436SPS.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF436SPS
Confidence label: medium.
Primary evidence
KitchenAid measurement source — dimension-guide-w11783878-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRFF436SPS.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF436SPS
Confidence label: medium.
Primary evidence
KitchenAid measurement source — dimension-guide-w11783878-reva.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
2" space behind Calculation or inference: documented DOE model pattern KRFF436SPS.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162611.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). full-page adjudication=3.75; parser candidates=[3.74, 3.75]; next to a fixed wall, leave a 3 3/4" (9.5 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). full-page adjudication=3.75; parser candidates=[3.74, 3.75]; next to a fixed wall, leave a 3 3/4" (9.5 cm
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
KitchenAid measurement source — 106162618.pdf Publisher not recorded
Page 2
Value used by ExactFit
14.0625 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162618.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-04
"To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
"To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162618.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-04
Product dimensions: G Cabinet width 35 13/16" (909 mm). The stored 35 15/16 was a retail figure.
Product dimensions: G Cabinet width 35 13/16" (909 mm). The stored 35 15/16 was a retail figure.
Other evidence found
35.94 in — superseded
www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Sibling-chassis propagation from KRFF436SJP; model codes have the same numeric skeleton, at least four existing chassis dimensions match, and no structural dimensions conflict. Sibling evidence: Cabinet Width: 35.94 in | iation of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 35.938 in Capacity 29.51 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 3. The final reviewed registry supersedes this earlier audit value.
Selected: 70.0625 in. Earlier retained values: 70.06 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Rounding normalised 2026-10-22: the stored 70.06 in is the same printed dimension as 70 1/16 in (70.0625); every finish of the KRFF436S family carries the same value to within 0.02 in. Source kept as stored. Calculation or inference: same-chassis variant propagation from KRFF436SJP.
Selected: 36.9375 in. Earlier retained values: 36.1875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
KitchenAid's installation documents for KRFF436SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and 1/2 (1." Opening width = 35.9375 + 1/2 + 1/2 = 36.9375 in. The earlier 36.1875 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 35.9375 + 2 * 0.5 = 36.9375.
Evidence reflects the sources reviewed on 2026-10-31. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
