Measurement evidence for KitchenAid KRFF336SPS

Value used by ExactFit

35.94 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — p.31-cu.-ft.-french-door-refrigerator-with-interior-water-and-ice.krff336sps.html
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: net Width: 35.94 in | on of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Ca
Reviewed: 2026-09-04

net Width: 35.94 in | on of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 35.938 in Capacity 30.52 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 3

Why this value was used

net Width: 35.94 in | on of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 35.938 in Capacity 30.52 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 3

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162608.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

C* Height to top of cabinet -> 69" (1753 mm)

Why this value was used

C* Height to top of cabinet -> 69" (1753 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.06 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — p.31-cu.-ft.-french-door-refrigerator-with-interior-water-and-ice.krff336sps.html
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height To Top Of Door Hinge: 70.06 in | 1 cu. ft. Gross Weight 298 lbs Height 70.0625 in Height To T
Reviewed: 2026-09-04

Height To Top Of Door Hinge: 70.06 in | 1 cu. ft. Gross Weight 298 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 283 lbs Refrigerator

Why this value was used

Height To Top Of Door Hinge: 70.06 in | 1 cu. ft. Gross Weight 298 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 283 lbs Refrigerator

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162608.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Depth without doors -> 297/8" (758.8 mm)

Why this value was used

F Depth without doors -> 297/8" (758.8 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162608.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

E Depth with doors -> 343/4" (882.3 mm)

Why this value was used

E Depth with doors -> 343/4" (882.3 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

37.4375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162608.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with door handle -> 377/16"(951.3 mm)

Why this value was used

Depth with door handle -> 377/16"(951.3 mm)

Other evidence found

• 90 in — superseded

  www.abcwarehouse.com; location not retained. Model scope: not separately recorded. Raw value: product depth : Depth With Door Open 90 Degree . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 90 in — superseded

  www.abcwarehouse.com; location not retained. Model scope: not separately recorded. Raw value: product depth : Depth With Door Open 90 Degree . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — p.31-cu.-ft.-french-door-refrigerator-with-interior-water-and-ice.krff336sps.html
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 37.438 in Depth Excluding
Reviewed: 2026-09-04

Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 37.438 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 298 lbs Height 70.0625 in Hei

Why this value was used

Depth With Door Open 90 = 49.0 in | .75 in Depth Closed Including Handles 37.438 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 298 lbs Height 70.0625 in Hei

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.94 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.94 + 2 * 0.5 = 36.94

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162611.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-10-31

KitchenAid's installation documents for KRFF336SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and 1/2 (1." Opening width = 35.94 + 1/2 + 1/2 = 36.94 in. The earlier 36.19 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).

Why this value was used

KitchenAid's installation documents for KRFF336SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and 1/2 (1." Opening width = 35.94 + 1/2 + 1/2 = 36.94 in. The earlier 36.19 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 35.94 + 2 * 0.5 = 36.94.

Other evidence found

• 36.19 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 36.19 in | idth 35.938 in Capacity 30.52 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36.188 in Depth 37.4375 in Depth Closed Excluding Handles 34.75 in Depth Closed Including. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.56 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.06 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.06 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF336SPS

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF336SPS.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF336SPS

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF336SPS.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF336SPS

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRFF336SPS.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF336SPS

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11783876-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2" space behind

Why this value was used

2" space behind Calculation or inference: documented DOE model pattern KRFF336SPS.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162611.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-10-25

Exact-model installation instructions: "When installing your refrigerator next to a fixed wall, leave a 3 3/4" (9.5 cm) minimum space between the refrigerator and wall to allow for the door to swing open." Door angle not stated; recorded as the 90° wall clearance as for other models with this wording.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model installation instructions: "When installing your refrigerator next to a fixed wall, leave a 3 3/4" (9.5 cm) minimum space between the refrigerator and wall to allow for the door to swing open." Door angle not stated; recorded as the 90° wall clearance as for other models with this wording.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

14.0625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162608.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-04

"To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

"To allow for a full door swing, you will need to leave 14 1/16" (357 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162608.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-04

Product dimensions: G Cabinet width 35 13/16" (909 mm). The stored 35 15/16 was a retail figure.

Why this value was used

Product dimensions: G Cabinet width 35 13/16" (909 mm). The stored 35 15/16 was a retail figure.

Other evidence found

• 35.94 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Cabinet Width: 35.94 in | iation of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 35.938 in Capacity 30.52 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 3. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.