Measurement evidence for KitchenAid KRFF333SPS

Value used by ExactFit

32.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* product width = 32 7/8 in.
Reviewed: 2026-09-04

KRFF333S* product width = 32 7/8 in.

Why this value was used

KRFF333S* product width = 32 7/8 in.

Other evidence found

• 35.625 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Aligned with case_width_in (35.625"). The final reviewed registry supersedes this earlier audit value. KRFF333S* product width = 32 7/8 in.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Height to top of cabinet B = 68 7/8 in.
Reviewed: 2026-09-04

KRFF333S* Height to top of cabinet B = 68 7/8 in.

Why this value was used

KRFF333S* Height to top of cabinet B = 68 7/8 in.

Other evidence found

• 68.5 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Height to top of cabinet 68¹/2" (174 cm). The final reviewed registry supersedes this earlier audit value. KRFF333S* Height to top of cabinet B = 68 7/8 in.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid KRFF333SPS Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Height 701/8" (178.1 cm)

Why this value was used

Overall Height 701/8" (178.1 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Depth of cabinet only G = 28 1/8 in.
Reviewed: 2026-09-04

KRFF333S* Depth of cabinet only G = 28 1/8 in.

Why this value was used

KRFF333S* Depth of cabinet only G = 28 1/8 in.

Other evidence found

• 24.125 in — superseded

  105605178.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: Depth of cabinet only -> 241/8". The final reviewed registry supersedes this earlier audit value. KRFF333S* Depth of cabinet only G = 28 1/8 in.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Depth without handles F = 32 in.
Reviewed: 2026-09-04

KRFF333S* Depth without handles F = 32 in.

Why this value was used

KRFF333S* Depth without handles F = 32 in.

Other evidence found

• 28 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Depth without handles 28" (71.1 cm). The final reviewed registry supersedes this earlier audit value. KRFF333S* Depth without handles F = 32 in.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Depth with handles E = 34 1/2 in.
Reviewed: 2026-09-04

KRFF333S* Depth with handles E = 34 1/2 in.

Why this value was used

KRFF333S* Depth with handles E = 34 1/2 in.

Other evidence found

• 29.375 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with handles 293/8" (74.6 cm). The final reviewed registry supersedes this earlier audit value. KRFF333S* Depth with handles E = 34 1/2 in.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Depth with doors open 90 degrees C = 47 1/8 in.
Reviewed: 2026-09-04

KRFF333S* Depth with doors open 90 degrees C = 47 1/8 in.

Why this value was used

KRFF333S* Depth with doors open 90 degrees C = 47 1/8 in.

Other evidence found

• 43 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with doors open 90° 43" (109.2 cm). The final reviewed registry supersedes this earlier audit value. KRFF333S* Depth with doors open 90 degrees C = 47 1/8 in.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 32.875 + 2 * 0.5 = 33.875

Confidence label: medium.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening derived from exact 32 7/8 in cabinet width and documented 1/2 in ventilation on each
Reviewed: 2026-09-04

Minimum opening derived from exact 32 7/8 in cabinet width and documented 1/2 in ventilation on each side.

Why this value was used

Minimum opening derived from exact 32 7/8 in cabinet width and documented 1/2 in ventilation on each side. Calculation or inference: 32.875 + 2 * 0.5 = 33.875.

Other evidence found

• 33 in — superseded

  https://www.southernhomeappliance.com/en/product/873070-kitchenaid-krff333sps; location not retained. Model scope: not separately recorded. Raw value: Exact model listing: Cutout Width 33.0 in. The final reviewed registry supersedes this earlier audit value. Minimum opening derived from exact 32 7/8 in cabinet width and documented 1/2 in ventilation on each side.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF333SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF333SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF333SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF333SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF333SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRFF333SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF333SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern KRFF333SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.48 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid KRFF333SPS Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

(6.3 cm) minimum on the hinge side

Why this value was used

(6.3 cm) minimum on the hinge side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: KRFF333S* Width of cabinet H = 32 7/8 in.
Reviewed: 2026-09-04

KRFF333S* Width of cabinet H = 32 7/8 in.

Why this value was used

KRFF333S* Width of cabinet H = 32 7/8 in.

Other evidence found

• 35.625 in — superseded

  105605185.pdf; page 1. Model scope: not separately recorded. Raw value: Width of cabinet 355/8" (90.5 cm). The final reviewed registry supersedes this earlier audit value. KRFF333S* Width of cabinet H = 32 7/8 in.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

2.4803 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid KRFF333SPS Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

(6.3 cm) minimum on the hinge side

Why this value was used

(6.3 cm) minimum on the hinge side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.