Measurement evidence for KitchenAid KRFF330SPS

Value used by ExactFit

30.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162679.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-31

KitchenAid KRFF330S Product Dimensions (W11820239A) p1: "H Width of Cabinet 30 1/8" (76.5 cm)". The stored 29 1/2 in was a retail label figure (Codex measurement review 2026-10-31).

Why this value was used

KitchenAid KRFF330S Product Dimensions (W11820239A) p1: "H Width of Cabinet 30 1/8" (76.5 cm)". The stored 29 1/2 in was a retail label figure (Codex measurement review 2026-10-31).

Other evidence found

• 29.5 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed cached exact-model manufacturer label: net Width = 29.5 in. Context: on of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 29.5 in Capacity 19.68 cu. ft. Common Size 30 in Cutout Height 68 in Cutout Width 30 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162679.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to Top of Cabinet 671/2" (171.5 cm)

Why this value was used

Height to Top of Cabinet 671/2" (171.5 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.38 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — p.20-cu.-ft.-30-inch-width-standard-depth-french-door-refrigerator-with-printshield-finish-and-interior-dispense.krff330sps.html
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height To Top Of Door Hinge: 68.38 in | u. ft. Gross Weight 259.6 lbs Height 68.375 in Height To Top
Reviewed: 2026-09-04

Height To Top Of Door Hinge: 68.38 in | u. ft. Gross Weight 259.6 lbs Height 68.375 in Height To Top Of Cabinet 67.5 in Height To Top Of Door Hinge 68.375 in Maximum Height 68.375 in Minimum Height 67.5 in Net Weight 254.6 lbs Refrigerat

Why this value was used

Height To Top Of Door Hinge: 68.38 in | u. ft. Gross Weight 259.6 lbs Height 68.375 in Height To Top Of Cabinet 67.5 in Height To Top Of Door Hinge 68.375 in Maximum Height 68.375 in Minimum Height 67.5 in Net Weight 254.6 lbs Refrigerat

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162679.pdf (p.5)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-04

Depth of Cabinet Only -> 28" (71.1 cm)

Why this value was used

Depth of Cabinet Only -> 28" (71.1 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162679.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth without Handles 321/4" (81.9 cm)

Why this value was used

Depth without Handles 321/4" (81.9 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162679.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with Handles 35" (88.8 cm)

Why this value was used

Depth with Handles 35" (88.8 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44.12 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — p.20-cu.-ft.-30-inch-width-standard-depth-french-door-refrigerator-with-printshield-finish-and-interior-dispense.krff330sps.html
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Excluding Doors 28 in Depth With Door Open 90: 44.12 in | epth Closed Excluding Handles 32.25
Reviewed: 2026-09-04

Depth Excluding Doors 28 in Depth With Door Open 90: 44.12 in | epth Closed Excluding Handles 32.25 in Depth Closed Including Handles 34.875 in Depth Excluding Doors 28 in Depth With Door Open 90 Degree 44.125 in Freezer Capacity Volume 6.34 cu. ft. Gross Weight 259.6 lbs Height 68.375 in He

Why this value was used

Depth Excluding Doors 28 in Depth With Door Open 90: 44.12 in | epth Closed Excluding Handles 32.25 in Depth Closed Including Handles 34.875 in Depth Excluding Doors 28 in Depth With Door Open 90 Degree 44.125 in Freezer Capacity Volume 6.34 cu. ft. Gross Weight 259.6 lbs Height 68.375 in He

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 30.125 + 2 * 0.5 = 31.125

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162679.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-31

KitchenAid's installation documents for KRFF330SPS print no cutout width; they ask for 1/2 in of space on each side: "KRFF330S dimension guide p2 location drawing: 1/2" (1.25 cm) on each side and on top." Opening width = 30.125 + 1/2 + 1/2 = 31.125 in. The earlier 30.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).

Why this value was used

KitchenAid's installation documents for KRFF330SPS print no cutout width; they ask for 1/2 in of space on each side: "KRFF330S dimension guide p2 location drawing: 1/2" (1.25 cm) on each side and on top." Opening width = 30.125 + 1/2 + 1/2 = 31.125 in. The earlier 30.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 30.125 + 2 * 0.5 = 31.125.

Other evidence found

• 30 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 30.0 in | inet Width 29.5 in Capacity 19.68 cu. ft. Common Size 30 in Cutout Height 68 in Cutout Width 30 in Depth 34.875 in Depth Closed Excluding Handles 32.25 in Depth Closed Including . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 30 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 30.0 in | inet Width 29.5 in Capacity 19.68 cu. ft. Common Size 30 in Cutout Height 68 in Cutout Width 30 in Depth 34.875 in Depth Closed Excluding Handles 32.25 in Depth Closed Including . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.88 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 68.38 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 68.38 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF330SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern KRFF330SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF330SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern KRFF330SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF330SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side and at the top

Why this value was used

1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern KRFF330SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF330SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11820239-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" space behind

Why this value was used

1" space behind Calculation or inference: documented DOE model pattern KRFF330SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162678.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). full-page adjudication=2.0; parser candidates=[2.48, 2.0]; next to a fixed wall, leave a 2" (6.3 cm

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). full-page adjudication=2.0; parser candidates=[2.48, 2.0]; next to a fixed wall, leave a 2" (6.3 cm

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162679.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-04

Product Dimensions for KRFF330S: H Width of Cabinet 30 1/8" (76.5 cm). The stored 29 1/2 was a retail figure.

Why this value was used

Product Dimensions for KRFF330S: H Width of Cabinet 30 1/8" (76.5 cm). The stored 29 1/2 was a retail figure.

Other evidence found

• 29.5 in — superseded

  www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Cabinet Width: 29.5 in | iation of Home Appliance Manufacturers) Sustainability Standards ### Dimensions Cabinet Width 29.5 in Capacity 19.68 cu. ft. Common Size 30 in Cutout Height 68 in Cutout Width 30 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.