Measurement evidence for KitchenAid KRBR130SPS

Value used by ExactFit

29.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model Cabinet Width: 29.625 in; prior 32.5 in came from a malformed retailer row.
Reviewed: 2026-09-04

Official exact-model Cabinet Width: 29.625 in; prior 32.5 in came from a malformed retailer row.

Why this value was used

Official exact-model Cabinet Width: 29.625 in; prior 32.5 in came from a malformed retailer row.

Other evidence found

• 32.5 in — superseded

  https://appliancehomestore.com/refrigeration/refrigerators/bottom-freezer-refrigerators/krbr130sps; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Width = 32.5 in | ght | 278 | | Total Refrigerator Capacity Volume | 18.7 | | Height | 69.5 in. | | Length | 36 in. | | Width | 32.5 in. | Exterior Details [...] Icemaker Details | | | --- | | Icemaker | Optional | | Icemaker Location | Freezer | | Types o. The final reviewed registry supersedes this earlier audit value. Official exact-model Cabinet Width: 29.625 in; prior 32.5 in came from a malformed retailer row.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height To Top Of Cabinet 65.5 in
Reviewed: 2026-09-04

Height To Top Of Cabinet 65.5 in

Why this value was used

Height To Top Of Cabinet 65.5 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height To Top Of Door Hinge = 67.0 in | 293 lbs, 293 lbs Height 67 in, 67 in Height To Top Of Cabin
Reviewed: 2026-09-04

Height To Top Of Door Hinge = 67.0 in | 293 lbs, 293 lbs Height 67 in, 67 in Height To Top Of Cabinet 65.5 in, 65.5 in Height To Top Of Door Hinge 67 in, 67 in Maximum Height 67 in, 67 in Minimum Height 65.5 in, 65.5 in Net Weight 2

Why this value was used

Height To Top Of Door Hinge = 67.0 in | 293 lbs, 293 lbs Height 67 in, 67 in Height To Top Of Cabinet 65.5 in, 65.5 in Height To Top Of Door Hinge 67 in, 67 in Maximum Height 67 in, 67 in Minimum Height 65.5 in, 65.5 in Net Weight 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Excluding Doors 28.125 in
Reviewed: 2026-09-04

Depth Excluding Doors 28.125 in

Why this value was used

Depth Excluding Doors 28.125 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Excluding Handles 30.875 in
Reviewed: 2026-09-04

Depth Closed Excluding Handles 30.875 in

Why this value was used

Depth Closed Excluding Handles 30.875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Including Handles 33.375 in
Reviewed: 2026-09-04

Depth Closed Including Handles 33.375 in

Why this value was used

Depth Closed Including Handles 33.375 in

Other evidence found

• 90 in — superseded

  https://www.townappliance.com/products/kitchenaid-krbr130sps-bottom-freezer-freestanding-refrigerator; location not retained. Model scope: not separately recorded. Raw value: product depth : Depth With Door Open 90 Degree . The final reviewed registry supersedes this earlier audit value. Depth Closed Including Handles 33.375 in

  Open alternative source ↗
• 90 in — superseded

  https://www.townappliance.com/products/kitchenaid-krbr130sps-bottom-freezer-freestanding-refrigerator; location not retained. Model scope: not separately recorded. Raw value: product depth : Depth With Door Open 90 Degree . The final reviewed registry supersedes this earlier audit value. Depth Closed Including Handles 33.375 in

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

59 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth With Door Open 90 = 59.0 in | cluding Handles 33.375 in, 33.375 in Depth Excluding Doors 28.12
Reviewed: 2026-09-04

Depth With Door Open 90 = 59.0 in | cluding Handles 33.375 in, 33.375 in Depth Excluding Doors 28.125 in, 28.125 in Depth With Door Open 90 Degree 59 in, 59 in Freezer Capacity Volume 5.73 cu. ft., 5.73 cu. ft. Gross Weight 293 lbs,

Why this value was used

Depth With Door Open 90 = 59.0 in | cluding Handles 33.375 in, 33.375 in Depth Excluding Doors 28.125 in, 28.125 in Depth With Door Open 90 Degree 59 in, 59 in Freezer Capacity Volume 5.73 cu. ft., 5.73 cu. ft. Gross Weight 293 lbs,

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cutout Width = 30.0 in | 8.67 cu. ft., 18.67 cu. ft. Common Size 30 in, 30 in Cutout Height 67 in, 6
Reviewed: 2026-09-04

Cutout Width = 30.0 in | 8.67 cu. ft., 18.67 cu. ft. Common Size 30 in, 30 in Cutout Height 67 in, 67 in Cutout Width 30 in, 30 in Depth 33.375 in, 33.375 in Depth Closed Excluding Handles 30.875 in, 30.

Why this value was used

Cutout Width = 30.0 in | 8.67 cu. ft., 18.67 cu. ft. Common Size 30 in, 30 in Cutout Height 67 in, 67 in Cutout Width 30 in, 30 in Depth 33.375 in, 33.375 in Depth Closed Excluding Handles 30.875 in, 30.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 67.0 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 67.0 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBR130SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRBR130SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBR130SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRBR130SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBR130SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRBR130SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBR130SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — https://www.kitchenaid.com/content/dam/global/documents/202510/dimension-guide-w11808667-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern KRBR130SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document

Confidence label: medium.

Primary evidence

Amana ABB1924BRB Owners Manual
assets.skulytics.io · Owners Manual
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

next to a fixed wall, leave 2 1/2" (6.3 cm

Why this value was used

next to a fixed wall, leave 2 1/2" (6.3 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

19 Cu. Ft. 30-Inch Bottom Mount Refrigerator with Right Door Swing and Preserva® Food Care System in PrintShield® Stainless Steel PrintShield Stainless KRBR130SPS | KitchenAid
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Cabinet Width 29.625 in.
Reviewed: 2026-09-04

Official exact-model page: Cabinet Width 29.625 in.

Why this value was used

Official exact-model page: Cabinet Width 29.625 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Freestanding Whirlpool-platform family side clearance

Confidence label: low.

Primary evidence

KitchenAid measurement source — local-cache manufacturer-family consensus
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.5 in per-side installation clearance from dominant manufacturer-family specification patt
Reviewed: 2026-09-04

Inferred 0.5 in per-side installation clearance from dominant manufacturer-family specification pattern.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.