Measurement evidence for KitchenAid KRBL133SPS

Value used by ExactFit

32.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Width of cabinet/product = 32 5/8 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Width of cabinet/product = 32 5/8 in.

Other evidence found

• 29.75 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Aligned with case_width_in (29.75"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Height to top of cabinet = 68 7/8 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Height to top of cabinet = 68 7/8 in.

Other evidence found

• 67.0079 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Table Top of Cabinet B: 177.8 cm (70.0"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Overall Height = 70 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Overall Height = 70 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf (p.4)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

Depth of cabinet only -> 281/8"

Why this value was used

Depth of cabinet only -> 281/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Depth without handles = 32 1/4 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Depth without handles = 32 1/4 in.

Other evidence found

• 30.875 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Depth without handles 307/8" (78.4 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Depth with handles = 33 3/4 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Depth with handles = 33 3/4 in.

Other evidence found

• 33.375 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with handles 33³/8" (84.8 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

62 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Depth with doors open 90 degrees = 62 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Depth with doors open 90 degrees = 62 in.

Other evidence found

• 70 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Table Doors Open 90 C: 177.8 cm (70.0"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 32.625 + 2 * 0.5 = 33.625

Confidence label: high.

Primary evidence

KitchenAid measurement source — 105605150.pdf
www.abt.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-10-31

KitchenAid's installation documents for KRBL133SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top." Opening width = 32.625 + 1/2 + 1/2 = 33.625 in. The earlier 33.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).

Why this value was used

KitchenAid's installation documents for KRBL133SPS print no cutout width; they ask for 1/2 in of space on each side: "To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top." Opening width = 32.625 + 1/2 + 1/2 = 33.625 in. The earlier 33.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 32.625 + 2 * 0.5 = 33.625.

Other evidence found

• 33 in — superseded

  www.abt.com; location not retained. Model scope: not separately recorded. Raw value: Exact model listing: Standard Cutout Width 33 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.0 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.0 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.125 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBL133SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRBL133SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBL133SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRBL133SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBL133SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRBL133SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRBL133SP***

Confidence label: medium.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808671-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern KRBL133SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

KitchenAid measurement source — 105605151.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Manufacturer location requirements: leave 2 1/2 in minimum on the hinge side next to a fixed wall.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Manufacturer location requirements: leave 2 1/2 in minimum on the hinge side next to a fixed wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605151.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual exact-model family table, KRBL133S* column: Width of cabinet = 32 5/8 in.

Why this value was used

Visual exact-model family table, KRBL133S* column: Width of cabinet = 32 5/8 in.

Other evidence found

• 29.75 in — superseded

  Document 105605151.pdf; page 1. Model scope: not separately recorded. Raw value: Width of cabinet 29³/4" (76.5 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.