Measurement evidence for KitchenAid KBSN748TPA

Value used by ExactFit

47.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — KBSN748TPA.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Width with Doors Closed 47 3/4 in.
Reviewed: 2026-09-04

Exact-model cached specification: Width with Doors Closed 47 3/4 in.

Why this value was used

Exact-model cached specification: Width with Doors Closed 47 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — kitchenaid-48-30-cu-ft-panel-ready-built-in-side-by-side-refrigerator-with-platinum-interior-kbsn748tpa-1894534
www.appliancedirect.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height To Top Of Cabinet: 83.125 in; supported by three cached exact-model retailer domains.
Reviewed: 2026-09-04

Height To Top Of Cabinet: 83.125 in; supported by three cached exact-model retailer domains.

Why this value was used

Height To Top Of Cabinet: 83.125 in; supported by three cached exact-model retailer domains.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

76.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — kitchenaid-KBSN748TPA
www.tascoappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model table: Height To Top Of Door Hinge 76.188 in.
Reviewed: 2026-09-07

Exact-model table: Height To Top Of Door Hinge 76.188 in.

Why this value was used

Exact-model table: Height To Top Of Door Hinge 76.188 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — KBSN748TPA.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door = 22.375 in | l Ready Built-In ... 19.13 Cu. Ft. Dimensions Width: 47 3/4 Inch De
Reviewed: 2026-09-04

Depth without Door = 22.375 in | l Ready Built-In ... 19.13 Cu. Ft. Dimensions Width: 47 3/4 Inch Depth: 24 Inch Depth without Door: 22 3/8 Inch Depth

Why this value was used

Depth without Door = 22.375 in | l Ready Built-In ... 19.13 Cu. Ft. Dimensions Width: 47 3/4 Inch Depth: 24 Inch Depth without Door: 22 3/8 Inch Depth

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — KBSN748TPA.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth without Handles 24 in.
Reviewed: 2026-09-04

Exact-model cached specification: Depth without Handles 24 in.

Why this value was used

Exact-model cached specification: Depth without Handles 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

24 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — kitchenaid-KBSN748TPA
www.tascoappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model table: Depth 24 in and Depth Closed Excluding Handles 24 in.
Reviewed: 2026-09-04

Exact-model table: Depth 24 in and Depth Closed Excluding Handles 24 in.

Why this value was used

Exact-model table: Depth 24 in and Depth Closed Excluding Handles 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — KBSN748TPA.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth with Door at 90 degrees 50 1/4 in.
Reviewed: 2026-09-04

Exact-model cached specification: Depth with Door at 90 degrees 50 1/4 in.

Why this value was used

Exact-model cached specification: Depth with Door at 90 degrees 50 1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162839.pdf
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-10-31

KitchenAid installation instructions p9 table: Model 48" - Opening Width (W) 48" (1219 mm). Replaces a store listing citation.

Why this value was used

KitchenAid installation instructions p9 table: Model 48" - Opening Width (W) 48" (1219 mm). Replaces a store listing citation.

Other evidence found

• 42 in — superseded

  Document 106162839.pdf; page 9. Model scope: not separately recorded. Raw value: Opening Width (W): 42.0 in | Opening Width (W) | 42" | 42" (1067 mm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: cached document family mapping: declared_multi_model_scope

Confidence label: medium.

Primary evidence

KitchenAid measurement source — 106162833.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Opening Height (H) Closed Recommended: 84"

Why this value was used

Opening Height (H) Closed Recommended: 84" Calculation or inference: cached document family mapping: declared_multi_model_scope.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162833.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

full-page adjudication=25.0; parser candidates=[25.0, 42.0]; Opening Depth (D) FLUSH Minimum: 25"

Why this value was used

full-page adjudication=25.0; parser candidates=[25.0, 42.0]; Opening Depth (D) FLUSH Minimum: 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (KitchenAid doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (KitchenAid doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 106162515.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.

Why this value was used

Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: medium.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

KitchenAid measurement source — 106162833.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

KitchenAid built-in opening residual: 25.0 - 22.375 = 2.625 in behind the case within the accepted opening.

Why this value was used

KitchenAid built-in opening residual: 25.0 - 22.375 = 2.625 in behind the case within the accepted opening. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 106162833.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 59
Reviewed: 2026-10-04

Door swing dimensions: "The location must permit both doors to open to a minimum of 90°. Allow 4 1/2" (114 mm) minimum space between the side of the refrigerator and a corner wall."

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Door swing dimensions: "The location must permit both doors to open to a minimum of 90°. Allow 4 1/2" (114 mm) minimum space between the side of the refrigerator and a corner wall."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — KBSN748TPA.html
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Cabinet Width 48 in.
Reviewed: 2026-09-04

Exact-model cached specification: Cabinet Width 48 in.

Why this value was used

Exact-model cached specification: Cabinet Width 48 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.