Measurement evidence for KitchenAid KBFN542SPS

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to KitchenAid KBFN542SPS fit check Check this model against your opening How ExactFit verifies measurements

KitchenAid KBFN542SPS

Built-in French Door · Built-in
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

7exact-model manufacturer values

0verified equivalent/same-chassis values

6secondary-source-only values

1estimated values (not printed for this model)

2values with unresolved source details

Last reviewed: 2026-10-29. 6 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	41.1875 in	✓ Conflicting sources — resolved	KitchenAid measurement source — 106162569.pdf KitchenAid	Page 1
Value used by ExactFit 41.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — 106162569.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22 KitchenAid product dimensions W11783104A (KBFN542SPS, KBFN542SJP, KBFN542SBE) p.1 table: B Overall Width 41 3/16" (1046.7 mm), as stored for KBFN542SJP. Replaces the kitchenaid.com figure 41.5 in, which is the cutout width, not the appliance. Open original source ↗ Why this value was used KitchenAid product dimensions W11783104A (KBFN542SPS, KBFN542SJP, KBFN542SBE) p.1 table: B Overall Width 41 3/16" (1046.7 mm), as stored for KBFN542SJP. Replaces the kitchenaid.com figure 41.5 in, which is the cutout width, not the appliance. Other evidence found 41.5 in — superseded www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed cached exact-model manufacturer label: net Width = 41.5 in. Context: rial Metal Handle Type Reach Through Handle Hidden Hinge Yes ### Dimensions Cabinet Width 41.5 in Capacity 24.2 cu. ft. Cutout Depth 24 in Cutout Height 83.5 in Cutout Width 41.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	83.1875 in	✓ Conflicting sources — resolved	KitchenAid measurement source — KBFN542SPS-106162569.pdf assets.skulytics.io	Page 4
Value used by ExactFit 83.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — KBFN542SPS-106162569.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-27 Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.1875 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.25 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case. Open original source ↗ Why this value was used Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.1875 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.25 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case. Other evidence found 74.25 in — superseded Document 106162569.pdf; page 4. Model scope: not separately recorded. Raw value: Visual side-view table: Cabinet Height = 74 1/4 in.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	83.1875 in	✓ Verified — retained secondary source	KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io	Page 3
Value used by ExactFit 83.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Overall Height -> 833∕16" (2113.5 mm) Open original source ↗ Why this value was used Overall Height -> 833∕16" (2113.5 mm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	23.375 in	✓ Conflicting sources — resolved	KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid	Retained specification excerpt: kitchenaid.com exact-model page: "Depth Excluding Doors 23.375 in"; the stored 23.38 was the page's
Value used by ExactFit 23.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: kitchenaid.com exact-model page: "Depth Excluding Doors 23.375 in"; the stored 23.38 was the page's Reviewed: 2026-10-22 kitchenaid.com exact-model page: "Depth Excluding Doors 23.375 in"; the stored 23.38 was the page's rounded figure. Open original source ↗ Why this value was used kitchenaid.com exact-model page: "Depth Excluding Doors 23.375 in"; the stored 23.38 was the page's rounded figure. Other evidence found 23.38 in — superseded The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Depth Excluding Doors: 23.38 in \| Depth Closed Excluding Handles 25.75 in Depth Closed Including Handles 27.81 in Depth Excluding Doors 23.375 in Depth With Door Open 90 Degree 44.25 in Freezer Capacity Volume 6.4 cu. ft. Gro. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	25.75 in	✓ Verified — retained secondary source	KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io	Page 3
Value used by ExactFit 25.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Depth without Handle -> 253∕4" (654.7 mm) Open original source ↗ Why this value was used Depth without Handle -> 253∕4" (654.7 mm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	27.8125 in	✓ Verified — retained secondary source	KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io	Page 3
Value used by ExactFit 27.8125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid installation document — 106162571.pdf (p.3) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04 Depth with Handle -> 2713∕16" (706 mm) Open original source ↗ Why this value was used Depth with Handle -> 2713∕16" (706 mm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	44.25 in	✓ Verified — exact model	KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid	Retained specification excerpt: Depth With Door Open 90: 44.25 in \| 5.75 in Depth Closed Including Handles 27.81 in Depth Excluding
Value used by ExactFit 44.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90: 44.25 in \| 5.75 in Depth Closed Including Handles 27.81 in Depth Excluding Reviewed: 2026-09-04 Depth With Door Open 90: 44.25 in \| 5.75 in Depth Closed Including Handles 27.81 in Depth Excluding Doors 23.375 in Depth With Door Open 90 Degree 44.25 in Freezer Capacity Volume 6.4 cu. ft. Gross Weight 612.85 lbs Height 83.187 in He Open original source ↗ Why this value was used Depth With Door Open 90: 44.25 in \| 5.75 in Depth Closed Including Handles 27.81 in Depth Excluding Doors 23.375 in Depth With Door Open 90 Degree 44.25 in Freezer Capacity Volume 6.4 cu. ft. Gross Weight 612.85 lbs Height 83.187 in He Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	41.5 in	✓ Conflicting sources — resolved	KitchenAid measurement source — 106162580.pdf assets.skulytics.io	Page 9
Value used by ExactFit 41.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — 106162580.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-10-14 Standard Installation (24" cabinet depth): Opening Width (W) 42" model 41 1/2" to 41 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04). Open original source ↗ Why this value was used Standard Installation (24" cabinet depth): Opening Width (W) 42" model 41 1/2" to 41 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04). Other evidence found 43.25 in — superseded Document 106162569.pdf; page 7. Model scope: not separately recorded. Raw value: Model Total Opening Width (W) Width Between Cleats (X) -> 42" 431/4" to 431/2" (1098 mm to 1105 mm) 411/2" to 413/4" (1054 mm to 1061 mm). The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	83.5 in	✓ Verified — exact model	KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid	Retained specification excerpt: Cutout Height 83.5 in
Value used by ExactFit 83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Height 83.5 in Reviewed: 2026-09-05 Cutout Height 83.5 in Open original source ↗ Why this value was used Cutout Height 83.5 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	24 in	✓ Verified — exact model	KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid	Retained specification excerpt: Cutout Depth 24 in
Value used by ExactFit 24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Depth 24 in Reviewed: 2026-09-05 Cutout Depth 24 in Open original source ↗ Why this value was used Cutout Depth 24 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.188 in	≈ Estimated — not printed for this model	ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.188 in	≈ Estimated — not printed for this model	ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.75 in	✓ Verified — retained secondary source	KitchenAid installation document — 106162569.pdf assets.skulytics.io	Page 6
Value used by ExactFit 0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid installation document — 106162569.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-05 Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille. Open original source ↗ Why this value was used Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	0.625 in	✓ Conflicting sources — resolved · Calculated/inferred	KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid	Retained specification excerpt: KitchenAid built-in opening residual: cutout depth 24.0 - depth excluding doors 23.375 = 0.625 in (r
Value used by ExactFit 0.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidence KitchenAid measurement source — p.24.2-cu.-ft.-42-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn542sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: KitchenAid built-in opening residual: cutout depth 24.0 - depth excluding doors 23.375 = 0.625 in (r Reviewed: 2026-10-22 KitchenAid built-in opening residual: cutout depth 24.0 - depth excluding doors 23.375 = 0.625 in (recalculated after the rounding fix). Open original source ↗ Why this value was used KitchenAid built-in opening residual: cutout depth 24.0 - depth excluding doors 23.375 = 0.625 in (recalculated after the rounding fix). Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence found 0.62 in — superseded The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: KitchenAid built-in opening residual: 24.0 - 23.38 = 0.62 in behind the case within the accepted opening.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	2.75 in	? Verified — finalized database measurement	KitchenAid measurement source — 106162551.pdf Publisher not recorded	Page 5
Value used by ExactFit 2.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — 106162551.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-25 Exact-model KitchenAid built-in dimension guide, top view, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to the open door. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used Exact-model KitchenAid built-in dimension guide, top view, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to the open door. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	41.1875 in	✓ Conflicting sources — resolved	KitchenAid measurement source — 106162569.pdf KitchenAid	Page 1
Value used by ExactFit 41.1875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence KitchenAid measurement source — 106162569.pdf KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22 KitchenAid product dimensions W11783104A (KBFN542SPS, KBFN542SJP, KBFN542SBE) p.1 table: B Overall Width 41 3/16" (1046.7 mm), as stored for KBFN542SJP. Replaces the kitchenaid.com figure 41.5 in, which is the cutout width, not the appliance. Open original source ↗ Why this value was used KitchenAid product dimensions W11783104A (KBFN542SPS, KBFN542SJP, KBFN542SBE) p.1 table: B Overall Width 41 3/16" (1046.7 mm), as stored for KBFN542SJP. Replaces the kitchenaid.com figure 41.5 in, which is the cutout width, not the appliance. Other evidence found 41.5 in — superseded www.kitchenaid.com; location not retained. Model scope: not separately recorded. Raw value: Official exact-model page: Cabinet Width 41.5 in.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Overall width

Selected: 41.1875 in. Earlier retained values: 41.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

KitchenAid product dimensions W11783104A (KBFN542SPS, KBFN542SJP, KBFN542SBE) p.1 table: B Overall Width 41 3/16" (1046.7 mm), as stored for KBFN542SJP. Replaces the kitchenaid.com figure 41.5 in, which is the cutout width, not the appliance.

View source scope, location, and impact on fit

Cabinet height

Selected: 83.1875 in. Earlier retained values: 74.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.1875 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.25 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case.

View source scope, location, and impact on fit

Depth without door

Selected: 23.375 in. Earlier retained values: 23.38 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

kitchenaid.com exact-model page: "Depth Excluding Doors 23.375 in"; the stored 23.38 was the page's rounded figure.

View source scope, location, and impact on fit

Minimum cutout width

Selected: 41.5 in. Earlier retained values: 43.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Standard Installation (24" cabinet depth): Opening Width (W) 42" model 41 1/2" to 41 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04).

View source scope, location, and impact on fit

Rear clearance

Selected: 0.625 in. Earlier retained values: 0.62 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

KitchenAid built-in opening residual: cutout depth 24.0 - depth excluding doors 23.375 = 0.625 in (recalculated after the rounding fix). Calculation or inference: min_cutout_depth_in - depth_case_only_in.

View source scope, location, and impact on fit

Cabinet case width

Selected: 41.1875 in. Earlier retained values: 41.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages