This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 6 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — KBFN536SPS-106162542.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 4 Reviewed: 2026-10-27
Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.25 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.3125 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case.
Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.25 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.3125 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case.
Other evidence found
74.3125 in — superseded
Document 106162542.pdf; page 4. Model scope: not separately recorded. Raw value: Visual side-view table: Cabinet Height = 74 5/16 in.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth Excluding Doors 23.68 in
Value used by ExactFit
23.68 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn536sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Excluding Doors 23.68 in Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Retained specification excerpt: Depth With Door Open 90 Degree 41.25 in
Value used by ExactFit
41.25 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn536sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90 Degree 41.25 in Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162580.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-10-14
Standard Installation (24" cabinet depth): Opening Width (W) 36" model 35 1/2" to 35 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04).
Standard Installation (24" cabinet depth): Opening Width (W) 36" model 35 1/2" to 35 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04).
Other evidence found
37.25 in — superseded
Document 106162542.pdf; page 7. Model scope: not separately recorded. Raw value: Model
Total Opening Width (W)
Width Between Cleats (X) -> 36"
371/4" to 371/2" (946 mm to 952 mm)
351/2" to 353/4" (902 mm to 908 mm). The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Height 83.5 in
Value used by ExactFit
83.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn536sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Height 83.5 in Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Depth 24 in
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn536sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Depth 24 in Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit
Not printed for this model
Value used by ExactFit
0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.
Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate)
Confidence label: low.
Primary evidence
ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29
Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.
No document we have for this model prints this value.
Why this value was used
Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit
Not printed for this model
Value used by ExactFit
0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.
Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate)
Confidence label: low.
Primary evidence
ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29
Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.
No document we have for this model prints this value.
Why this value was used
Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-05
Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.
Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-french-door-bottom-mount-refrigerator-with-platinum-interior.kbfn536sps.html KitchenAid · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: KitchenAid built-in opening residual: 24.0 - 23.68 = 0.32 in behind the case within the accepted ope Reviewed: 2026-09-05
KitchenAid built-in opening residual: 24.0 - 23.68 = 0.32 in behind the case within the accepted opening.
KitchenAid built-in opening residual: 24.0 - 23.68 = 0.32 in behind the case within the accepted opening. Calculation or inference: min_cutout_depth_in - depth_case_only_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
KitchenAid measurement source — 106162524.pdf Publisher not recorded
Page 5
Value used by ExactFit
2.75 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid measurement source — 106162524.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-25
Exact-model KitchenAid built-in dimension guide, top view, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to the open door.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Exact-model KitchenAid built-in dimension guide, top view, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to the open door.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
KitchenAid installation document — 106162542.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 83.25 in. Earlier retained values: 74.3125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model KitchenAid dimension guide, page 4 side view: Overall Height 83.25 in (top of the unit, including the top machine compartment). The previously stored 'Cabinet Height' (74.3125 in) is line D on the drawing: the back of the cabinet below the machine compartment, not the top of the case.
Selected: 35.5 in. Earlier retained values: 37.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Standard Installation (24" cabinet depth): Opening Width (W) 36" model 35 1/2" to 35 3/4"; front 1 3/4" proud of the cabinetry. The standard opening is stored, not the flush one (owner decision 2026-10-04).
Model numbers covered: KBFN536SPS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
