This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.68 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit32.68 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.79 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit65.79 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.38 in | ✓ Conflicting sources — resolved · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit66.38 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 27.56 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit27.56 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.75 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit30.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.75 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit30.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 65.43 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: Conflict-free finish/model variant of the documented Kenmore chassis. | |
Value used by ExactFit65.43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 899.6133# color suffix Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html Conflict-free finish/model variant of the documented Kenmore chassis.Open original source ↗ Why this value was usedConflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 38.68 in | ✓ Verified — retained secondary source · Calculated/inferred | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit38.68 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 32.68 + 2 * 3.0 Confidence label: medium. Primary evidenceKenmore measurement source — 101719970.pdf Exact width plus the manual's required clearance on both sides.Open original source ↗ Why this value was usedExact width plus the manual's required clearance on both sides. Calculation or inference: 32.68 + 2 * 3.0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.38 in | ✓ Verified — retained secondary source · Calculated/inferred | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit69.38 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceKenmore measurement source — 101719970.pdf Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.Open original source ↗ Why this value was usedMinimum opening height is the verified highest appliance endpoint plus the documented top clearance. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.56 in | ✓ Verified — retained secondary source · Calculated/inferred | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit30.56 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceKenmore measurement source — 101719970.pdf Minimum opening depth is the verified cabinet depth plus the documented rear clearance.Open original source ↗ Why this value was usedMinimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Endpoint migration from reviewed side_clearance_wall_in; evidence explicitly states each/both sides Confidence label: high. Primary evidenceKenmore measurement source — 101719970.pdf Stored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.0 in on each side and on the hinge side at a fixed wall.Open original source ↗ Why this value was usedStored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.0 in on each side and on the hinge side at a fixed wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 3 in | ✓ Verified — retained secondary source | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Endpoint migration from reviewed side_clearance_wall_in; evidence explicitly states each/both sides Confidence label: high. Primary evidenceKenmore measurement source — 101719970.pdf Stored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.0 in on each side and on the hinge side at a fixed wall.Open original source ↗ Why this value was usedStored reviewed evidence explicitly applies the clearance to each/both sides. Manual requires 3.0 in on each side and on the hinge side at a fixed wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3 in | ✓ Verified — retained secondary source · Calculated/inferred | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKenmore measurement source — 101719970.pdf Manufacturer family manual requires 3 in at the top, rear, and each side.Open original source ↗ Why this value was usedManufacturer family manual requires 3 in at the top, rear, and each side. Calculation or inference: cached documented shared chassis propagation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 3 in | ✓ Verified — retained secondary source · Calculated/inferred | Kenmore measurement source — 101719970.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKenmore measurement source — 101719970.pdf Manufacturer family manual requires 3 in at the top, rear, and each side.Open original source ↗ Why this value was usedManufacturer family manual requires 3 in at the top, rear, and each side. Calculation or inference: cached documented shared chassis propagation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3 in | ✓ Verified — retained secondary source | Kenmore measurement source — prod_27603923012 i.sears.com | Page 10 | |
Value used by ExactFit3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKenmore measurement source — prod_27603923012 When installing your refrigerator next to a fixed wall, leave a 3” (7.6 cm) minimum space on the hinge side (some models require more) to allow the door to swing open. (door angle not stated). Source covers: The exact Kenmore 46-61335 product page links this Use & Care Guide; the guide’s model table lists family 899.6133# (the final digit is the color number).. Checked on the rendered page. Found by the Hermes second pass 2026-10-25.Open original source ↗ Why this value was usedWhen installing your refrigerator next to a fixed wall, leave a 3” (7.6 cm) minimum space on the hinge side (some models require more) to allow the door to swing open. (door angle not stated). Source covers: The exact Kenmore 46-61335 product page links this Use & Care Guide; the guide’s model table lists family 899.6133# (the final digit is the color number).. Checked on the rendered page. Found by the Hermes second pass 2026-10-25. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.68 in | ✓ Verified — exact model · Calculated/inferred | Kenmore measurement source — 61332.html Kenmore | Retained specification excerpt: No side projections; standardized case width to official closed-door width. | |
Value used by ExactFit32.68 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case width = exact closed-door width Confidence label: medium. Primary evidenceKenmore measurement source — 61332.html No side projections; standardized case width to official closed-door width.Open original source ↗ Why this value was usedNo side projections; standardized case width to official closed-door width. Calculation or inference: case width = exact closed-door width. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 66.38 in. Earlier retained values: 90 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Conflict-free finish/model variant of the documented Kenmore chassis. Calculation or inference: 899.6133# color suffix.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Kenmore · Web source · exact model/source
Model numbers covered: 46-61335. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: 46-61335. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗i.sears.com · Web source · secondary model/source
Model numbers covered: 46-61335. Publication/revision date: Not recorded. Reviewed: 2026-10-25.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.