Measurement evidence for Kenmore 46-51805

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.97 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

• 90 in — superseded

  southernappliances.net; location not retained. Model scope: not separately recorded. Raw value: height to top of hinge (in.) : Depth w/Door Open 90 Degrees (In.) . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.02 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.64 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.24 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

45.74 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official Kenmore structured product specification.
Reviewed: 2026-09-04

Official Kenmore structured product specification.

Why this value was used

Official Kenmore structured product specification.

Other evidence found

• 90 in — superseded

  southernappliances.net; location not retained. Model scope: not separately recorded. Raw value: depth w/door open 90 degrees (in.) : Width w/Door Open 90 Degrees (In.) . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 36.0 + 2 * 4.0

Confidence label: medium.

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-04

Exact width plus the manual's required 4-in clearance on both sides.

Why this value was used

Exact width plus the manual's required 4-in clearance on both sides. Calculation or inference: 36.0 + 2 * 4.0.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

82 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-10-23

Recalculated with the stored formula: height to top of hinge 70.00 in (Kenmore spec) + top clearance 12 in (manual drawing) = 82 in.

Why this value was used

Recalculated with the stored formula: height to top of hinge 70.00 in (Kenmore spec) + top clearance 12 in (manual drawing) = 82 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

• 74 in — superseded

  The same document as the value used above; page 10. Model scope: not separately recorded. Raw value: Minimum opening height is the verified highest appliance endpoint plus the documented top clearance.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.02 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Minimum opening depth is the verified cabinet depth plus the documented rear clearance.

Why this value was used

Minimum opening depth is the verified cabinet depth plus the documented rear clearance. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['both sides']; Diagram requires 4 in on both sides.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['both sides']; Diagram requires 4 in on both sides.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['both sides']; Diagram requires 4 in on both sides.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['both sides']; Diagram requires 4 in on both sides.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

12 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-10-23

Installation clearance drawing (page 10) for Kenmore 46-51805: 12" (30 cm) above the refrigerator; 4" (10 cm) at each side and behind. The old 4.0 applied the side/rear value to the top.

Why this value was used

Installation clearance drawing (page 10) for Kenmore 46-51805: 12" (30 cm) above the refrigerator; 4" (10 cm) at each side and behind. The old 4.0 applied the side/rear value to the top.

Other evidence found

• 4 in — superseded

  The same document as the value used above; page 10. Model scope: not separately recorded. Raw value: Exact-model manufacturer installation diagram specifies 4 in surrounding clearance.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Kenmore measurement source — 101719960.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Exact-model manufacturer installation diagram specifies 4 in surrounding clearance.

Why this value was used

Exact-model manufacturer installation diagram specifies 4 in surrounding clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.66 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: (37.32 - 36) / 2

Confidence label: medium.

Primary evidence

Kenmore measurement source — kenmore-51805-20-cu-ft-side-by-side-refrigerator-8211-fingerprint-resistant-stainless-steel
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Manufacturer page/document for Exact product page: Model # 46-51805: Width w/Door Open 90 Degrees (I
Reviewed: 2026-10-25

Manufacturer page/document for Exact product page: Model # 46-51805: Width w/Door Open 90 Degrees (In.):37.32; Width w/ Door Closed (In.):36. Found 2026-10-25.

Why this value was used

Manufacturer page/document for Exact product page: Model # 46-51805: Width w/Door Open 90 Degrees (In.):37.32; Width w/ Door Closed (In.):36. Found 2026-10-25.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case width = exact closed-door width

Confidence label: medium.

Primary evidence

Kenmore measurement source — 51805.html
Kenmore · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: No side projections; standardized case width to official closed-door width.
Reviewed: 2026-09-04

No side projections; standardized case width to official closed-door width.

Why this value was used

No side projections; standardized case width to official closed-door width. Calculation or inference: case width = exact closed-door width.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.