This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 70.875 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit70.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 71.875 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit71.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 29.4375 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit29.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 32.375 in | ✓ Conflicting sources — resolved | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit32.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 44.25 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit44.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72.125 in | ✓ Secondary source only · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit72.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf Minimum opening height derived from highest stored appliance endpoint 71.875 in plus documented top clearance 0.25 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 71.875 in plus documented top clearance 0.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26 in | ✓ Secondary source only · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.1875 in | ✓ Verified — exact model · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCI72S*** Confidence label: medium. Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf 3/16" space on each sideOpen original source ↗ Why this value was used3/16" space on each side Calculation or inference: documented DOE model pattern JFFCCI72S***. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.1875 in | ✓ Verified — exact model · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCI72S*** Confidence label: medium. Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf 3/16" space on each sideOpen original source ↗ Why this value was used3/16" space on each side Calculation or inference: documented DOE model pattern JFFCCI72S***. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.25 in | ✓ Verified — exact model · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCI72S*** Confidence label: medium. Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf 3/16" space on each side and 1/4" space at the topOpen original source ↗ Why this value was used3/16" space on each side and 1/4" space at the top Calculation or inference: documented DOE model pattern JFFCCI72S***. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — exact model · Calculated/inferred | JennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf JennAir | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCI72S*** Confidence label: medium. Primary evidenceJennAir measurement source — https://www.jennair.com/content/dam/global/documents/202505/dimension-guide-w11778231-reva.pdf 1" space behindOpen original source ↗ Why this value was used1" space behind Calculation or inference: documented DOE model pattern JFFCCI72S***. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 3.75 in | ✓ Secondary source only · Calculated/inferred | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: declared_multi_model_scope Confidence label: medium. Primary evidenceJennAir JFFCCI72SL Dimension Guide next to a fixed wall, leave a 33/4" (9.5 cmOpen original source ↗ Why this value was usednext to a fixed wall, leave a 33/4" (9.5 cm Calculation or inference: cached document family mapping: declared_multi_model_scope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Secondary source only | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 3.75 in | ✓ Conflicting sources — resolved | JennAir JFFCCI72SL Dimension Guide assets.skulytics.io | Page 2 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir JFFCCI72SL Dimension Guide JennAir exact-model-family dimension table and fixed-wall requirement.Open original source ↗ Why this value was usedJennAir exact-model-family dimension table and fixed-wall requirement. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 32.375 in. Earlier retained values: 32.38 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir exact-model-family dimension table and fixed-wall requirement.
View source scope, location, and impact on fitSelected: 3.75 in. Earlier retained values: 0.1875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir exact-model-family dimension table and fixed-wall requirement.
View source scope, location, and impact on fitassets.skulytics.io · Dimension Guide · secondary model/source
Model numbers covered: JFFCCI72SL. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir · Web source · exact model/source
Model numbers covered: JFFCCI72SL. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.