Measurement evidence for JennAir JFFCCE72SL

Value used by ExactFit

35.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 25 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Width Cabinet H: 25.0". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 31.5748 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Top of Cabinet B: 80.2 cm (31.5748"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 32.3661 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Overall Height A: 82.21 cm (32.3661"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.4375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 35.6299 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Depth Without Handles F: 35.6299". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 70.8661 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Doors Open 90 C: 180.0 cm (70.8661"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

72.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 71.875 in plus documented top clearance 0.25 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 71.875 in plus documented top clearance 0.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCE72S***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

3/16" of space on each side

Why this value was used

3/16" of space on each side Calculation or inference: documented DOE model pattern JFFCCE72S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCE72S***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

3/16" of space on each side

Why this value was used

3/16" of space on each side Calculation or inference: documented DOE model pattern JFFCCE72S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCE72S***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

3/16" of space on each side and 1/4" space at the top

Why this value was used

3/16" of space on each side and 1/4" space at the top Calculation or inference: documented DOE model pattern JFFCCE72S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JFFCCE72S***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11778234-reva.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" space behind

Why this value was used

1" space behind Calculation or inference: documented DOE model pattern JFFCCE72S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

JennAir measurement source — 105803580.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from side_clearance_wall_in (door angle not stated, 6 in or less). JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

Migrated from side_clearance_wall_in (door angle not stated, 6 in or less). JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105803580.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model-family dimension table and fixed-wall requirement.

Why this value was used

JennAir exact-model-family dimension table and fixed-wall requirement.

Other evidence found

• 25 in — superseded

  Document 105803580.pdf; page 1. Model scope: not separately recorded. Raw value: Table Width Cabinet H: 25.0". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.