Measurement evidence for JennAir JF42NXFXDE

Value used by ExactFit

41.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

82.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

82.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — p.42-inch-built-in-french-door-refrigerator.jf42nxfxde.html
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 23.5 in. Context: epth Close
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 23.5 in. Context: epth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 23.5 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 5.9 cu. ft. Gro

Why this value was used

Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 23.5 in. Context: epth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 23.5 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 5.9 cu. ft. Gro

Other evidence found

• 24 in — superseded

  Document 105167318.pdf; page 1. Model scope: not separately recorded. Raw value: 413⁄4" (W) x 827/8" (H) x 24" (depth without door panels/handles). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

• 43.7402 in — superseded

  Document 105167318.pdf; page 3. Model scope: not separately recorded. Raw value: Table Depth Without Handles F: 43.7402". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.6875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — 105167318.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-24

Minimum depth with handle: 27-11/16" with the RISE Stainless handle, 26-7/8" with the NOIR Stainless handle; depth without handles 24-3/4". The deeper handle is stored, as for the JF36NXFXDE sibling. The previous 27.38 in came from a web page.

Why this value was used

Minimum depth with handle: 27-11/16" with the RISE Stainless handle, 26-7/8" with the NOIR Stainless handle; depth without handles 24-3/4". The deeper handle is stored, as for the JF36NXFXDE sibling. The previous 27.38 in came from a web page.

Other evidence found

• 27.38 in — superseded

  www.jennair.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: 83.25 in Cutout Width 42 in Depth 24 in Depth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 23.5 in Depth With Door Open 90 Degree 43.75 in Freezer C. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

42 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

JennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — 105167318.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Manufacturer planning guide specifies a 25 in finished enclosure depth.

Why this value was used

Manufacturer planning guide specifies a 25 in finished enclosure depth.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

JennAir measurement source — 105167318.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

JennAir measurement source — 105167318.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JF42NXFXDE**

Confidence label: medium.

Primary evidence

JennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

1/8" of open space above the refrigerator

Why this value was used

1/8" of open space above the refrigerator Calculation or inference: documented DOE model pattern JF42NXFXDE**.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_less_handles_in

Confidence label: high.

Calculation inputs: Depth with door, without handles; Minimum cutout depth;

Primary evidence

JennAir measurement source — 105167318.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

25 in enclosure minus 24 3/4 in finished product depth = 1/4 in.

Why this value was used

25 in enclosure minus 24 3/4 in finished product depth = 1/4 in. Calculation or inference: min_cutout_depth_in - depth_less_handles_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — 105160622.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-24

FRENCH DOOR BOTTOM MOUNT MODELS, DOOR SWING DIMENSIONS: The location must permit both doors to open to a minimum of 90 degrees. Allow 4 1/2" (11.4 cm) minimum space between the side of the refrigerator and a corner wall. NOTE: More clearance may be required with wood overlay panels, custom handles, or extended handles.

Why this value was used

FRENCH DOOR BOTTOM MOUNT MODELS, DOOR SWING DIMENSIONS: The location must permit both doors to open to a minimum of 90 degrees. Allow 4 1/2" (11.4 cm) minimum space between the side of the refrigerator and a corner wall. NOTE: More clearance may be required with wood overlay panels, custom handles, or extended handles.

Other evidence found

• 2.375 in — superseded

  Document 105167318.pdf; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Legacy reviewed field migration; endpoint indicators=['90-degree']; Conservative RISE handle-to-wall requirement.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

41.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 105167318.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model integrated French-door guide.

Why this value was used

JennAir exact-model integrated French-door guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.