Measurement evidence for JennAir JBSS48E22L

Value used by ExactFit

48.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

• 42 in — superseded

  Document 90391104.pdf; page 3. Model scope: not separately recorded. Raw value: Aligned with case_width_in (42.0"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — JBSS42E22L-90391097.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-27

JennAir shared 42/48 in factory-panel side-by-side dimension guide (names JBSS42E22L and JBSS48E22L), page 4 side view: D Height to top of machine compartment cover 83 3/16 in (top of the case); A Total height 83 3/8 in. The previously stored 71 in is line C 'Height of Cabinet': the back of the cabinet below the machine compartment, not the top of the case.

Why this value was used

JennAir shared 42/48 in factory-panel side-by-side dimension guide (names JBSS42E22L and JBSS48E22L), page 4 side view: D Height to top of machine compartment cover 83 3/16 in (top of the case); A Total height 83 3/8 in. The previously stored 71 in is line C 'Height of Cabinet': the back of the cabinet below the machine compartment, not the top of the case.

Other evidence found

• 74.5 in — superseded

  www.jennair.com; location not retained. Model scope: not separately recorded. Raw value: Height To Top Of Cabinet: 74.5 in | 8 in Freezer Capacity Volume 10.3 cu. ft. Gross Weight 673 lbs Height 83.375 in Height To Top Of Cabinet 74.5 in Net Weight 619 lbs Refrigerator Capacity Volume 19.1 Total Refrigerator Capacit. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 71 in — superseded

  Document 90391097.pdf; page 4. Model scope: not separately recorded. Raw value: JennAir shared 42/48 factory-panel side-by-side dimension guide.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.6875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.6875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

• 50.69 in — superseded

  www.jennair.com; location not retained. Model scope: not separately recorded. Raw value: Depth With Door Open 90: 50.69 in | 25 in Depth Closed Including Handles 27.688 in Depth Excluding Doors 22.375 in Depth With Door Open 90 Degree 50.688 in Freezer Capacity Volume 10.3 cu. ft. Gross Weight 673 lbs Height 83.375 in Heig. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

JennAir measurement source — dimension-guide-w11593506-revB.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 83.375 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 83.375 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

JennAir measurement source — installation-instruction-w11686646-revA.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

The side panel should be a minimum of | 1/2" (1.27 cm) thick to avoid warping. | If the opening depth is 25" (63.5 cm) or more, you

Why this value was used

The side panel should be a minimum of | 1/2" (1.27 cm) thick to avoid warping. | If the opening depth is 25" (63.5 cm) or more, you

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSS48E22***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11593506-revB.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern JBSS48E22***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSS48E22***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11593506-revB.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern JBSS48E22***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSS48E22***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11593506-revB.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1/2" of space on each side and at the top

Why this value was used

1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern JBSS48E22***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSS48E22***

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11593506-revB.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern JBSS48E22***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — ed6774a026cfc7867063c5122a20fe2d2cc110bfcdfa2a7bed1e09c2fd761933.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-10-14

Door swing dimensions: "The location must permit both doors to open to a minimum of 90°. Allow 4 1/2" minimum space between the side of the refrigerator and a corner wall." The stored 2 in came from a generic family mapping.

Why this value was used

Door swing dimensions: "The location must permit both doors to open to a minimum of 90°. Allow 4 1/2" minimum space between the side of the refrigerator and a corner wall." The stored 2 in came from a generic family mapping.

Other evidence found

• 2 in — superseded

  Document 90391097.pdf; page 4. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391097.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 factory-panel side-by-side dimension guide.

Other evidence found

• 42 in — superseded

  Document 90391104.pdf; page 3. Model scope: not separately recorded. Raw value: Cabinet Width 42". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.