Measurement evidence for JennAir JBSFS48NMX

Value used by ExactFit

48.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

• 42 in — superseded

  Document 90391081.pdf; page 3. Model scope: not separately recorded. Raw value: Aligned with case_width_in (42.0"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.12 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir measurement source — p.panel-ready-48-built-in-side-by-side-refrigerator.jbsfs48nmx.html
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Height To Top Of Cabinet = 83.12 in. Context: 5 in F
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Height To Top Of Cabinet = 83.12 in. Context: 5 in Freezer Capacity Volume 10.3 cu. ft. Gross Weight 647 lbs Height 83.125 in Height To Top Of Cabinet 83.125 in Net Weight 597 lbs Refrigerator Capacity Volume 19.1 Total Refrigerator Capacit

Why this value was used

Reviewed cached exact-model manufacturer label: Height To Top Of Cabinet = 83.12 in. Context: 5 in Freezer Capacity Volume 10.3 cu. ft. Gross Weight 647 lbs Height 83.125 in Height To Top Of Cabinet 83.125 in Net Weight 597 lbs Refrigerator Capacity Volume 19.1 Total Refrigerator Capacit

Other evidence found

• 71 in — superseded

  Document 90391074.pdf; page 4. Model scope: not separately recorded. Raw value: JennAir shared 42/48 panel-ready side-by-side dimension guide.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

• 83.125 in — superseded

  www.jennair.com; location not retained. Model scope: not separately recorded. Raw value: Official exact-model product-page Dimensions block: Height = 83.125 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in door depth + standard 1-in custom handle

Confidence label: medium.

Primary evidence

JennAir measurement source — 90391074.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

NMX is panel-ready; custom handle projection standardized to 1 in.

Why this value was used

NMX is panel-ready; custom handle projection standardized to 1 in. Calculation or inference: 24-in door depth + standard 1-in custom handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

JennAir measurement source — installation-insruction-w11686647-revA.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 83.4375 in plus documented top clearance 0.125 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 83.4375 in plus documented top clearance 0.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

JennAir measurement source — dimension-guide-w11576983-revD.pdf
JennAir · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 22.375 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 22.375 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSFS48NMX**

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11576983-revD.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern JBSFS48NMX**.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSFS48NMX**

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11576983-revD.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern JBSFS48NMX**.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSFS48NMX**

Confidence label: medium.

Primary evidence

JennAir measurement source — installation-insruction-w11686647-revA.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

1/8" of open space above the refrigerator

Why this value was used

1/8" of open space above the refrigerator Calculation or inference: documented DOE model pattern JBSFS48NMX**.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JBSFS48NMX**

Confidence label: medium.

Primary evidence

JennAir measurement source — dimension-guide-w11576983-revD.pdf
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern JBSFS48NMX**.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

JennAir measurement source — 90391074.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Shared JBSFS42/JBSFS48 installation guide specifies 2 in hinge-side wall clearance.

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Shared JBSFS42/JBSFS48 installation guide specifies 2 in hinge-side wall clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir installation document — 90391074.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Why this value was used

JennAir shared 42/48 panel-ready side-by-side dimension guide.

Other evidence found

• 42 in — superseded

  Document 90391081.pdf; page 3. Model scope: not separately recorded. Raw value: Cabinet Width 42". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.