This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.75 in | ✓ Conflicting sources — resolved | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5 in | ✓ Verified — retained secondary source | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5 in | ✓ Verified — retained secondary source | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.875 in | ✓ Conflicting sources — resolved | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit23.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.5 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit24.5 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 23.875-in raw unit + installed door/front Confidence label: medium. Primary evidenceJennAir measurement source — 106009448.pdf Exact platform installed depth is 24 1/2 in.Open original source ↗ Why this value was usedExact platform installed depth is 24 1/2 in. Calculation or inference: 23.875-in raw unit + installed door/front. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.125 in | ✓ Conflicting sources — resolved · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit27.125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented Pro-Style 27 1/8-in column configuration Confidence label: medium. Primary evidenceJennAir measurement source — 106009448.pdf Handle option standardized to Pro-Style configuration.Open original source ↗ Why this value was usedHandle option standardized to Pro-Style configuration. Calculation or inference: documented Pro-Style 27 1/8-in column configuration. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 56.375 in | ✓ Verified — retained secondary source | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit56.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Verified — retained secondary source | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 106009448.pdf Manufacturer guide specifies an 84 in opening height.Open original source ↗ Why this value was usedManufacturer guide specifies an 84 in opening height. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 106009448.pdf Manufacturer guide specifies a 25 in standard opening depth; 24 in is conditional on the trim kit.Open original source ↗ Why this value was usedManufacturer guide specifies a 25 in standard opening depth; 24 in is conditional on the trim kit. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceJennAir measurement source — 106009448.pdf 30 in opening minus 29 3/4 in product width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used30 in opening minus 29 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceJennAir measurement source — 106009448.pdf 30 in opening minus 29 3/4 in product width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used30 in opening minus 29 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Minimum cutout height; Primary evidenceJennAir measurement source — 106009448.pdf 84 in opening minus 83 1/2 in product height = 1/2 in.Open original source ↗ Why this value was used84 in opening minus 83 1/2 in product height = 1/2 in. Calculation or inference: min_cutout_height_in - height_hinge_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.5 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_less_handles_in Confidence label: high. Calculation inputs: Depth with door, without handles; Minimum cutout depth; Primary evidenceJennAir measurement source — 106009448.pdf 25 in opening minus 24 1/2 in finished product depth = 1/2 in.Open original source ↗ Why this value was used25 in opening minus 24 1/2 in finished product depth = 1/2 in. Calculation or inference: min_cutout_depth_in - depth_less_handles_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.5 in | ✓ Verified — retained secondary source | JennAir measurement source — 106009448.pdf assets.skulytics.io | Page 10 | |
Value used by ExactFit2.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceJennAir measurement source — 106009448.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Installation wall-gap diagram labels dimension C as 2 1/2 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Installation wall-gap diagram labels dimension C as 2 1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.75 in | ✓ Conflicting sources — resolved | JennAir installation document — 106009448.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 106009448.pdf Exact JennAir column installation dimensions and 30-in door-swing row.Open original source ↗ Why this value was usedExact JennAir column installation dimensions and 30-in door-swing row. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 29.75 in. Earlier retained values: 18 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact JennAir column installation dimensions and 30-in door-swing row.
View source scope, location, and impact on fitSelected: 23.875 in. Earlier retained values: 23.688 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact JennAir column installation dimensions and 30-in door-swing row.
View source scope, location, and impact on fitSelected: 27.125 in. Earlier retained values: 24.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Handle option standardized to Pro-Style configuration. Calculation or inference: documented Pro-Style 27 1/8-in column configuration.
View source scope, location, and impact on fitSelected: 29.75 in. Earlier retained values: 18 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact JennAir column installation dimensions and 30-in door-swing row.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: JBRFSR30RX. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.