Measurement evidence for JennAir JBRFL24IGX

Value used by ExactFit

23.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

24" Panel-Ready Built-In Column Refrigerator, Left Swing | JennAir
JennAir · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Including Handles = 27.125 in | t 84 in Cutout Width 24 in Depth 24.5 in Depth Closed E
Reviewed: 2026-09-04

Depth Closed Including Handles = 27.125 in | t 84 in Cutout Width 24 in Depth 24.5 in Depth Closed Excluding Handles 24.5 in Depth Closed Including Handles 27.125 in Depth Excluding Doors 23.688 in Depth With Door Open 90 Degree 50.438 in Gross

Why this value was used

Depth Closed Including Handles = 27.125 in | t 84 in Cutout Width 24 in Depth 24.5 in Depth Closed Excluding Handles 24.5 in Depth Closed Including Handles 27.125 in Depth Excluding Doors 23.688 in Depth With Door Open 90 Degree 50.438 in Gross

Other evidence found

• 27.12 in — superseded

  https://www.jennair.com/refrigeration/columns/column-refrigerators/p.24-panel-ready-built-in-column-refrigerator,-left-swing.jbrfl24igx.html; location not retained. Model scope: not separately recorded. Raw value: Depth Closed Including Handles: 27.12 in | t 84 in Cutout Width 24 in Depth 24.5 in Depth Closed Excluding Handles 24.5 in Depth Closed Including Handles 27.125 in Depth Excluding Doors 23.688 in Depth With Door Open 90 Degree 50.438 in Gross . The final reviewed registry supersedes this earlier audit value. Depth Closed Including Handles = 27.125 in | t 84 in Cutout Width 24 in Depth 24.5 in Depth Closed Excluding Handles 24.5 in Depth Closed Including Handles 27.125 in Depth Excluding Doors 23.688 in Depth With Door Open 90 Degree 50.438 in Gross

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.4375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

• 50.44 in — superseded

  https://www.jennair.com/refrigeration/columns/column-refrigerators/p.24-panel-ready-built-in-column-refrigerator,-left-swing.jbrfl24igx.html; location not retained. Model scope: not separately recorded. Raw value: Depth With Door Open 90: 50.44 in | 4.5 in Depth Closed Including Handles 27.125 in Depth Excluding Doors 23.688 in Depth With Door Open 90 Degree 50.438 in Gross Weight 467.5 lbs Height 83.5 in Height To Top Of Cabinet 84 in Net Weight. The final reviewed registry supersedes this earlier audit value. JennAir exact-model shared column planning guide.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

JennAir JBRFL24IGX 24 Inch Panel Ready Built-In Smart ...
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cutout Height: 84 Inches.
Reviewed: 2026-09-05

Cutout Height: 84 Inches.

Why this value was used

Cutout Height: 84 Inches.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

JennAir JBRFL24IGX 24 Inch Panel Ready Built-In Smart ...
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cutout Depth: 25 Inches.
Reviewed: 2026-09-05

Cutout Depth: 25 Inches.

Why this value was used

Cutout Depth: 25 Inches.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Cabinet case width; Minimum cutout width;

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Cabinet case width; Minimum cutout width;

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Nominal opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Minimum cutout height;

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

84 in opening minus 83 7/16 in appliance height = 9/16 in.

Why this value was used

84 in opening minus 83 7/16 in appliance height = 9/16 in. Calculation or inference: min_cutout_height_in - height_hinge_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_less_handles_in

Confidence label: high.

Calculation inputs: Depth with door, without handles; Minimum cutout depth;

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-05

25 in standard opening minus 24 1/2 in finished appliance depth = 1/2 in.

Why this value was used

25 in standard opening minus 24 1/2 in finished appliance depth = 1/2 in. Calculation or inference: min_cutout_depth_in - depth_less_handles_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Installation wall-gap diagram labels dimension C as 2 1/2 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

23.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

JennAir exact-model shared column planning guide.

Why this value was used

JennAir exact-model shared column planning guide.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

2.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared JennAir column opening table wall gap C

Confidence label: medium.

Primary evidence

JennAir ALOVE24RRC Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

2 1/2-in stainless-handle wall gap from the matching column installation platform.

Why this value was used

2 1/2-in stainless-handle wall gap from the matching column installation platform. Calculation or inference: shared JennAir column opening table wall gap C.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.