Overall width
Selected: 21.9375 in. Earlier retained values: 21.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir exact-model installation drawing.
View source scope, location, and impact on fitMeasurement evidence for JennAir JBBFX22NMX
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
JennAir JBBFX22NMX
Built-in Bottom Mount · Built-in
Market status: Active (recorded 2026-08-17)
Evidence summary
Complete mixed evidence
0exact-model manufacturer values
0verified equivalent/same-chassis values
14secondary-source-only values
2values with unresolved source details
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Measurements and supporting evidence
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 21.9375 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit21.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69.6875 in | ✓ Verified — retained secondary source | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit69.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.6875 in | ✓ Verified — retained secondary source | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit69.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.4375 in | ✓ Verified — retained secondary source | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit21.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 22.1875 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit22.1875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 21.4375-in chassis + 0.75-in panel Confidence label: medium. Primary evidenceJennAir measurement source — 90391721.pdf Standard 3/4-in furniture-panel installation.Open original source ↗ Why this value was usedStandard 3/4-in furniture-panel installation. Calculation or inference: 21.4375-in chassis + 0.75-in panel. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 23.1875 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit23.1875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 22.1875-in installed depth + 1-in handle Confidence label: medium. Primary evidenceJennAir measurement source — 90391721.pdf Custom handle projection standardized to 1 in.Open original source ↗ Why this value was usedCustom handle projection standardized to 1 in. Calculation or inference: 22.1875-in installed depth + 1-in handle. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 44.125 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit44.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 21.4375-in chassis + 21.9375-in door + 0.75-in panel Confidence label: medium. Primary evidenceJennAir measurement source — 90391721.pdf Geometric 90-degree extent for standard panel.Open original source ↗ Why this value was usedGeometric 90-degree extent for standard panel. Calculation or inference: 21.4375-in chassis + 21.9375-in door + 0.75-in panel. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 21.9375 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit21.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.938 in | ✓ Verified — retained secondary source | JennAir measurement source — JBBFX22NMX.html www.ajmadison.com | Retained specification excerpt: Cutout Height: 69 15/16" | |
Value used by ExactFit69.938 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceJennAir measurement source — JBBFX22NMX.html Cutout Height: 69 15/16"Open original source ↗ Why this value was usedCutout Height: 69 15/16" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 21.875 in | ✓ Verified — retained secondary source | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit21.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391721.pdf Installation diagram states a minimum interior frame depth of 21 7/8 in.Open original source ↗ Why this value was usedInstallation diagram states a minimum interior frame depth of 21 7/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0 in | ✓ Verified — retained secondary source | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391721.pdf The stated 21 15/16 in opening width equals product width; ventilation is through the separately documented bottom-to-top path.Open original source ↗ Why this value was usedThe stated 21 15/16 in opening width equals product width; ventilation is through the separately documented bottom-to-top path. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0 in | ✓ Verified — retained secondary source | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391721.pdf The stated 21 15/16 in opening width equals product width; ventilation is through the separately documented bottom-to-top path.Open original source ↗ Why this value was usedThe stated 21 15/16 in opening width equals product width; ventilation is through the separately documented bottom-to-top path. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | JennAir measurement source — jenn-air+jbbfx22nmx www.notice-facile.com | Retained specification excerpt: Allow a clearance minimum of 2" (50 mm) at the top | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceJennAir measurement source — jenn-air+jbbfx22nmx Allow a clearance minimum of 2" (50 mm) at the topOpen original source ↗ Why this value was usedAllow a clearance minimum of 2" (50 mm) at the top Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.4375 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 90391721.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceJennAir measurement source — 90391721.pdf 21 7/8 in frame depth minus 21 7/16 in cabinet depth = 7/16 in.Open original source ↗ Why this value was used21 7/8 in frame depth minus 21 7/16 in cabinet depth = 7/16 in. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 21.9375 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391721.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit21.9375 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391721.pdf JennAir exact-model installation drawing.Open original source ↗ Why this value was usedJennAir exact-model installation drawing. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Conflicting published measurements
Minimum cutout width
Selected: 21.9375 in. Earlier retained values: 22 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir exact-model installation drawing.
View source scope, location, and impact on fitCabinet case width
Selected: 21.9375 in. Earlier retained values: 21.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir exact-model installation drawing.
View source scope, location, and impact on fitMeasurements not established
Wall clearance for door open to 90°
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Wall clearance for fully open door
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Source documents and pages
JennAir installation document — 90391721.pdf
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: JBBFX22NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir measurement source — JBBFX22NMX.html
www.ajmadison.com · Web source · secondary model/source
Model numbers covered: JBBFX22NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Minimum cutout height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir measurement source — jenn-air+jbbfx22nmx
www.notice-facile.com · Web source · secondary model/source
Model numbers covered: JBBFX22NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Report a problem with this modelCheck whether JBBFX22NMX fits your openingBack to JennAir JBBFX22NMXRead the full verification methodology
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.