This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Built-in Bottom Mount · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-18. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.9375 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 81.25 in | ✓ Verified — retained secondary source | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit81.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 22 in | ✓ Conflicting sources — resolved | JennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html JennAir | Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 22.0 in. Context: t 84 in Cu | |
Value used by ExactFit22 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 22.0 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. GOpen original source ↗ Why this value was usedReviewed cached exact-model manufacturer label: Depth Excluding Doors = 22.0 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. G Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 24.75 in | ✓ Verified — retained secondary source | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 52.62 in | ✓ Conflicting sources — resolved | JennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html JennAir | Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Excluding Doors 22 in Depth With Door Open 90 | |
Value used by ExactFit52.62 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html Reviewed cached exact-model manufacturer label: Depth Excluding Doors 22 in Depth With Door Open 90 = 52.62 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. Gross Weight 410.05 lbs Height 80.7 in NetOpen original source ↗ Why this value was usedReviewed cached exact-model manufacturer label: Depth Excluding Doors 22 in Depth With Door Open 90 = 52.62 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. Gross Weight 410.05 lbs Height 80.7 in Net Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Verified — retained secondary source | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — exact model | JennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html JennAir | Retained specification excerpt: Cutout Height 84 in | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceJennAir measurement source — p.panel-ready-30-built-in-bottom-mount-refrigerator,-left-swing.jbbfl30nmx.html Cutout Height 84 inOpen original source ↗ Why this value was usedCutout Height 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — exact model | JennAir measurement source — 90391574.pdf JennAir | Page 11 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391574.pdf Opening dimensions: minimum opening depth 25" (635 mm), front plane of the opening to the rear wall; printed in both JennAir installation documents (90391574.pdf page 11 and the planning guide page 36). Replaces a calculated 22 3/16 in.Open original source ↗ Why this value was usedOpening dimensions: minimum opening depth 25" (635 mm), front plane of the opening to the rear wall; printed in both JennAir installation documents (90391574.pdf page 11 and the planning guide page 36). Replaces a calculated 22 3/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | JennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf JennAir | Page 9 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: corrected from full-page labeled dimension context Confidence label: high. Primary evidenceJennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf 3.2 mm) of space on each sideOpen original source ↗ Why this value was used3.2 mm) of space on each side Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | JennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf JennAir | Page 9 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: corrected from full-page labeled dimension context Confidence label: high. Primary evidenceJennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf 3.2 mm) of space on each sideOpen original source ↗ Why this value was used3.2 mm) of space on each side Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Verified — exact model | JennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf JennAir | Page 9 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: corrected from full-page labeled dimension context Confidence label: high. Primary evidenceJennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf 3.2 mm) of space on each side and at the topOpen original source ↗ Why this value was used3.2 mm) of space on each side and at the top Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.1969 in | ✓ Verified — exact model | JennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf JennAir | Page 21 | |
Value used by ExactFit0.1969 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: full-page semantic adjudication of parser alternatives Confidence label: high. Primary evidenceJennAir measurement source — 74a10a08ef1000c537fa55aa0dc4b580bff87bd27322733b5d0f52accdb61385.pdf 5 mm of space behindOpen original source ↗ Why this value was used5 mm of space behind Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 0.25 in | ? Verified — finalized database measurement | JennAir measurement source — 90391571.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit0.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391571.pdf Callout F: 1/4" beside the hinge with the door open 90 degrees using the supplied door stopper; printed in the spec sheet and the installation guide (the guide's metric value does not match its inches). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedCallout F: 1/4" beside the hinge with the door open 90 degrees using the supplied door stopper; printed in the spec sheet and the installation guide (the guide's metric value does not match its inches). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 7.25 in | ? Verified — finalized database measurement | JennAir measurement source — 90391571.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit7.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 90391571.pdf Callout A: 7 1/4" beside the hinge for the door fully open to the printed 105 degrees; printed in the spec sheet (page 1) and the installation guide (page 7). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedCallout A: 7 1/4" beside the hinge for the door fully open to the printed 105 degrees; printed in the spec sheet (page 1) and the installation guide (page 7). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.5 in | ✓ Conflicting sources — resolved | JennAir installation document — 90391571.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 90391571.pdf JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.Open original source ↗ Why this value was usedJennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 29.9375 in. Earlier retained values: 29.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.
View source scope, location, and impact on fitSelected: 22 in. Earlier retained values: 25 in, 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Depth Excluding Doors = 22.0 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. G
View source scope, location, and impact on fitSelected: 24.75 in. Earlier retained values: 24.8 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.
View source scope, location, and impact on fitSelected: 52.62 in. Earlier retained values: 39 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Depth Excluding Doors 22 in Depth With Door Open 90 = 52.62 in. Context: t 84 in Cutout Width 30 in Depth 24.8 in Depth Closed Excluding Handles 24.8 in Depth Excluding Doors 22 in Depth With Door Open 90 Degree 52.625 in Freezer Capacity Volume 4.09 cu. ft. Gross Weight 410.05 lbs Height 80.7 in Net
View source scope, location, and impact on fitSelected: 29.5 in. Earlier retained values: 29.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
JennAir JBBFL/JBBFR shared product-dimension drawing; integrated pull does not project.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: JBBFL30NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Minimum cutout width; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir · Web source · exact model/source
Model numbers covered: JBBFL30NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
3 displayed measurements supported: Depth without door; Depth with doors open at 90°; Minimum cutout height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir · Web source · exact model/source
Model numbers covered: JBBFL30NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-18.
1 displayed measurements supported: Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir · Web source · exact model/source
Model numbers covered: JBBFL30NMX. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-18. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.