This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Overall width. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Cabinet height. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Height with hinge / controlling height. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Depth without door. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Depth with door, without handles. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context:
Value used by ExactFit
27.38 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
36” Panel-Ready Built-In Bottom-Freezer Refrigerator (Right-Hand Door Swing) | JennAir JennAir · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: Reviewed: 2026-09-04
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: th 25 in Cutout Width 36 in Depth 24 in Depth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 24 in Depth With Door Open 90 Degree 58.75 in Freezer Cap
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: th 25 in Cutout Width 36 in Depth 24 in Depth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 24 in Depth With Door Open 90 Degree 58.75 in Freezer Cap
Other evidence found
26.875 in — superseded
105160612.pdf; page 3. Model scope: not separately recorded. Raw value: Depth with handle: 26 7/8" (68.2 cm). The final reviewed registry supersedes this earlier audit value. Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: th 25 in Cutout Width 36 in Depth 24 in Depth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 24 in Depth With Door Open 90 Degree 58.75 in Freezer Cap
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Minimum cutout width. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
JennAir measurement source — https://www.jennair.com/content/dam/global/documents/201906/w11286875-reva-armoire-kit-instructions.pdf JennAir · Web source Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in.
Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Why evidence from JB36NXFXLE applies
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: max(height_case_in,height_hinge_in) + top_clearance_in.
Measurement transferred: Minimum cutout height. Relevant equivalence evidence: Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in.. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Depth 25 in
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
36” Panel-Ready Built-In Bottom-Freezer Refrigerator (Right-Hand Door Swing) | JennAir JennAir · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Depth 25 in Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.
Why evidence from JB36NXFXLE applies
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: (min_cutout_width_in - case_width_in) / 2.
Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: 36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side.. Known differences: not separately recorded. Review decision: documented cavity residual formula; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.
Why evidence from JB36NXFXLE applies
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: (min_cutout_width_in - case_width_in) / 2.
Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: 36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side.. Known differences: not separately recorded. Review decision: documented cavity residual formula; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JB36NXFXRE**
Confidence label: medium.
Primary evidence
JennAir measurement source — https://www.jennair.com/content/dam/global/documents/201906/w11286875-reva-armoire-kit-instructions.pdf JennAir · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
1/8" of open space above the refrigerator Calculation or inference: documented DOE model pattern JB36NXFXRE**.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
25 in enclosure minus 24 3/4 in finished product depth = 1/4 in. Calculation or inference: min_cutout_depth_in - depth_less_handles_in.
Why evidence from JB36NXFXLE applies
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: min_cutout_depth_in - depth_less_handles_in.
Measurement transferred: Rear clearance. Relevant equivalence evidence: 25 in enclosure minus 24 3/4 in finished product depth = 1/4 in.. Known differences: not separately recorded. Review decision: documented cavity residual formula; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics. Original formula: documented RISE 90-degree handle projection K
Confidence label: medium.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
Legacy reviewed field migration; endpoint indicators=['90-degree']; Base unit supports RISE or NOIR; conservative RISE value used.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Target model: JB36NXFXRE. Supporting model: JB36NXFXLE. Manufacturer: JennAir. Product family and measurement relationship: JennAir shared exact-model integrated bottom-freezer guide..
Measurement transferred: Cabinet case width. Relevant equivalence evidence: JennAir shared exact-model integrated bottom-freezer guide.. Known differences: not separately recorded. Review decision: direct manual extraction; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented RISE 90-degree handle projection K
Confidence label: medium.
Primary evidence
JennAir JB36NXFXLE Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04
Base unit supports RISE or NOIR; conservative RISE value used.
Selected: 27.38 in. Earlier retained values: 26.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 27.38 in. Context: th 25 in Cutout Width 36 in Depth 24 in Depth Closed Excluding Handles 24.75 in Depth Closed Including Handles 27.375 in Depth Excluding Doors 24 in Depth With Door Open 90 Degree 58.75 in Freezer Cap
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.