This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Built-in Bottom Mount · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-18. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 82.875 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit82.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 82.875 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit82.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.875 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit26.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf Depth with handle: 26 7/8" (68.2 cm)Open original source ↗ Why this value was usedDepth with handle: 26 7/8" (68.2 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.625 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit58.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 83 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf JennAir | Page 8 | |
Value used by ExactFit83 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceJennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf Minimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 82.875 in plus documented top clearance 0.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | JennAir measurement source — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 105160618.pdf Manufacturer planning guide specifies a 25 in finished enclosure depth.Open original source ↗ Why this value was usedManufacturer planning guide specifies a 25 in finished enclosure depth. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceJennAir measurement source — 105160618.pdf 36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceJennAir measurement source — 105160618.pdf 36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side.Open original source ↗ Why this value was used36 in opening minus 35 3/4 in product width, divided equally = 1/8 in per side. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Verified — exact model · Calculated/inferred | JennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf JennAir | Page 8 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern JB36NXFXLE** Confidence label: medium. Primary evidenceJennAir measurement source — w11286875-reva-armoire-kit-instructions.pdf 1/8" of open space above the refrigeratorOpen original source ↗ Why this value was used1/8" of open space above the refrigerator Calculation or inference: documented DOE model pattern JB36NXFXLE**. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — retained secondary source · Calculated/inferred | JennAir measurement source — 105160618.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_less_handles_in Confidence label: high. Calculation inputs: Depth with door, without handles; Minimum cutout depth; Primary evidenceJennAir measurement source — 105160618.pdf 25 in enclosure minus 24 3/4 in finished product depth = 1/4 in.Open original source ↗ Why this value was used25 in enclosure minus 24 3/4 in finished product depth = 1/4 in. Calculation or inference: min_cutout_depth_in - depth_less_handles_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.5 in | ✓ Conflicting sources — resolved | JennAir measurement source — 105160622.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit4.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir measurement source — 105160622.pdf Minimum space between the side of the refrigerator and an adjacent corner wall so the door(s) can open at least 90 degrees: 4 1/2" (11.4 cm); more may be needed for overlay panels or projecting handles. Replaces a calculated 2 3/8 in.Open original source ↗ Why this value was usedMinimum space between the side of the refrigerator and an adjacent corner wall so the door(s) can open at least 90 degrees: 4 1/2" (11.4 cm); more may be needed for overlay panels or projecting handles. Replaces a calculated 2 3/8 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | JennAir installation document — 105160618.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceJennAir installation document — 105160618.pdf JennAir shared exact-model integrated bottom-freezer guide.Open original source ↗ Why this value was usedJennAir shared exact-model integrated bottom-freezer guide. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 4.5 in. Earlier retained values: 2.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Minimum space between the side of the refrigerator and an adjacent corner wall so the door(s) can open at least 90 degrees: 4 1/2" (11.4 cm); more may be needed for overlay panels or projecting handles. Replaces a calculated 2 3/8 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: JB36NXFXLE. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗JennAir · Web source · exact model/source
Model numbers covered: JB36NXFXLE. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: JB36NXFXLE. Publication/revision date: Not recorded. Reviewed: 2026-09-18.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-18. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.