This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 31.1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit31.1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.1 Instalation Dimension: Width (Excluding Door) 31.1", Width (Including Door) 31.1". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.1 Instalation Dimension: Width (Excluding Door) 31.1", Width (Including Door) 31.1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.5 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit68.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Height-Top of Cabinet "B" 68.5" (1740mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Height-Top of Cabinet "B" 68.5" (1740mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit69.1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Height-Overall "A" 69.1" (1756mm); p.1 Height (to Top of Hinge) 69.1". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Height-Overall "A" 69.1" (1756mm); p.1 Height (to Top of Hinge) 69.1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.6 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit23.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Cabinet "D" 23.6" (600mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Cabinet "D" 23.6" (600mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.6 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit26.6 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Door "E" 26.6" (675.5mm); p.1 Depth (Excluding Handles) 26.6". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Door "E" 26.6" (675.5mm); p.1 Depth (Excluding Handles) 26.6". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29.1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit29.1 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Handle "F" 29.1" (740mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-with Handle "F" 29.1" (740mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 56.3 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit56.3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-Doors Open 90 "J" 56.3" (1430mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Depth-Doors Open 90 "J" 56.3" (1430mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33.1 in | ? Verified — finalized database measurement · Calculated/inferred | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit33.1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: cabinet width 31.1 in + 2 x 1.0 in side space = 33.1 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: cabinet width 31.1 in + 2 x 1.0 in side space = 33.1 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.1 in | ? Verified — finalized database measurement · Calculated/inferred | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit70.1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: high. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: overall height 69.1 in + 1.0 in top space = 70.1 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: overall height 69.1 in + 1.0 in top space = 70.1 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25.6 in | ? Verified — finalized database measurement · Calculated/inferred | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit25.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: cabinet depth 23.6 in + 2.0 in rear space = 25.6 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE: cabinet depth 23.6 in + 2.0 in rear space = 25.6 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 Location Requirements: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Installation Clearance Sides 1". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 Location Requirements: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Installation Clearance Sides 1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 Location Requirements: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Installation Clearance Sides 1". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 Location Requirements: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Installation Clearance Sides 1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Top 1". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "allow for a 1.0" (25mm) space on each side and at the top"; p.1 Top 1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "Allow at least 2.0" (51mm) between back of cabinet and the wall"; p.1 Back 2". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "Allow at least 2.0" (51mm) between back of cabinet and the wall"; p.1 Back 2". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.6 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1.6 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "If you are installing your refrigerator next to a fixed wall, leave 1.6" (40mm) minimum on the hinge side ... to allow for the door to swing open." Door angle not stated. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2: "If you are installing your refrigerator next to a fixed wall, leave 1.6" (40mm) minimum on the hinge side ... to allow for the door to swing open." Door angle not stated. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 31.1 in | ? Verified — finalized database measurement | Hisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit31.1 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHisense measurement source — 4dcbaddbcfdf3089aee934b54a849e32fc10b01c02ac17988956d9b3d10b0ae9.pdf Hisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Width-Cabinet "C" 31.1" (790mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedHisense HRB171N6ASE spec sheet (c)2025, names HRB171N6ASE/AWE/ABE/BSE, p.2 table, HRB171N6ABE row: Width-Cabinet "C" 31.1" (790mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
16 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.