This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.75 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit29 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 33.375 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit33.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 33.375 in | ✓ Verified — exact model | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit33.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.75 in | ✓ Conflicting sources — resolved | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit48.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Haier installation document — 74717746.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier installation document — 74717746.pdf Installation manual states cabinet opening width B should not be less than 36 inches.Open original source ↗ Why this value was usedInstallation manual states cabinet opening width B should not be less than 36 inches. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS appliancehomestore.com | Retained specification excerpt: QNE27JY opening height uses the tallest exact appliance endpoint 69.75 in plus exact top air clearan | |
Value used by ExactFit70.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(68.625, 69.75) + 1 Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS QNE27JY opening height uses the tallest exact appliance endpoint 69.75 in plus exact top air clearance 1 in: 70.75 in.Open original source ↗ Why this value was usedQNE27JY opening height uses the tallest exact appliance endpoint 69.75 in plus exact top air clearance 1 in: 70.75 in. Calculation or inference: max(68.625, 69.75) + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS appliancehomestore.com | Retained specification excerpt: QNE27JY opening depth uses exact case-only depth 29 in plus exact rear air clearance 2 in: 29 + 2 = | |
Value used by ExactFit31 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29 + 2 Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS QNE27JY opening depth uses exact case-only depth 29 in plus exact rear air clearance 2 in: 29 + 2 = 31 in.Open original source ↗ Why this value was usedQNE27JY opening depth uses exact case-only depth 29 in plus exact rear air clearance 2 in: 29 + 2 = 31 in. Calculation or inference: 29 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Haier measurement source — qne27jymfs appliancehomestore.com | Retained specification excerpt: Side Air Clearances | 0.125 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — qne27jymfs Side Air Clearances | 0.125 inOpen original source ↗ Why this value was usedSide Air Clearances | 0.125 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Haier measurement source — qne27jymfs appliancehomestore.com | Retained specification excerpt: Side Air Clearances | 0.125 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — qne27jymfs Side Air Clearances | 0.125 inOpen original source ↗ Why this value was usedSide Air Clearances | 0.125 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Haier measurement source — qne27jymfs appliancehomestore.com | Retained specification excerpt: Top Air Clearances | 1 in | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — qne27jymfs Top Air Clearances | 1 inOpen original source ↗ Why this value was usedTop Air Clearances | 1 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Haier measurement source — qne27jymfs appliancehomestore.com | Retained specification excerpt: Back Air Clearances | 2 in | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — qne27jymfs Back Air Clearances | 2 inOpen original source ↗ Why this value was usedBack Air Clearances | 2 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS assets.skulytics.io | Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact | |
Value used by ExactFit4 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (43.75 - 35.75) / 2 Confidence label: high. Primary evidenceHaier measurement source — Haier-ENERGY-STAR-27-0-Cu-Ft-Fingerprint-Resistant-French-Door-Refrigerator-QNE27JYMFS Migrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact Haier width open 90 degrees is 43.75 in and closed width is 35.75 in; exact per-side operating envelope is (43.75 - 35.75) / 2 = 4 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact Haier width open 90 degrees is 43.75 in and closed width is 35.75 in; exact per-side operating envelope is (43.75 - 35.75) / 2 = 4 in. Calculation or inference: (43.75 - 35.75) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Haier installation document — 74717747.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier installation document — 74717747.pdf Width (in.) H -> 35-3/4Open original source ↗ Why this value was usedWidth (in.) H -> 35-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 48.75 in. Earlier retained values: 48.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: QNE27JYMFS. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: QNE27JYMFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗appliancehomestore.com · Web source · secondary model/source
Model numbers covered: QNE27JYMFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: QNE27JYMFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.