This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 27.75 in | ✓ Conflicting sources — resolved | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit27.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68 in | ✓ Verified — exact model | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit68 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Conflicting sources — resolved | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.25 in | ✓ Verified — exact model | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit24.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.625 in | ✓ Verified — exact model | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit26.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.875 in | ✓ Verified — exact model | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit26.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 38 in | ✓ Verified — exact model | Haier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Haier | Retained specification excerpt: Current exact-model Haier official weights and dimensions specification. | |
Value used by ExactFit38 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 14-5-cu-ft-4-door-refrigerator-qjs15hyrfs Current exact-model Haier official weights and dimensions specification.Open original source ↗ Why this value was usedCurrent exact-model Haier official weights and dimensions specification. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 27.75 in | ✓ Verified — exact model · Calculated/inferred | Haier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS Haier | Retained specification excerpt: QJS15HY opening width uses the exact current Haier closed envelope 27.75 in plus the exact Haier sid | |
Value used by ExactFit27.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 27.75 + 2 * 0 Confidence label: high. Primary evidenceHaier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS QJS15HY opening width uses the exact current Haier closed envelope 27.75 in plus the exact Haier side air clearance 0 in on both sides: 27.75 + 2 * 0 = 27.75 in.Open original source ↗ Why this value was usedQJS15HY opening width uses the exact current Haier closed envelope 27.75 in plus the exact Haier side air clearance 0 in on both sides: 27.75 + 2 * 0 = 27.75 in. Calculation or inference: 27.75 + 2 * 0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 69.875 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS assets.skulytics.io | Retained specification excerpt: QJS15HY opening height uses the tallest exact appliance endpoint 69.875 in plus exact top air cleara | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(68, 69.875) + 0 Confidence label: high. Primary evidenceHaier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS QJS15HY opening height uses the tallest exact appliance endpoint 69.875 in plus exact top air clearance 0 in: 69.875 in.Open original source ↗ Why this value was usedQJS15HY opening height uses the tallest exact appliance endpoint 69.875 in plus exact top air clearance 0 in: 69.875 in. Calculation or inference: max(68, 69.875) + 0. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS assets.skulytics.io | Retained specification excerpt: QJS15HY opening depth uses exact case-only depth 24.25 in plus exact rear air clearance 2 in: 24.25 | |
Value used by ExactFit26.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.25 + 2 Confidence label: high. Primary evidenceHaier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS QJS15HY opening depth uses exact case-only depth 24.25 in plus exact rear air clearance 2 in: 24.25 + 2 = 26.25 in.Open original source ↗ Why this value was usedQJS15HY opening depth uses exact case-only depth 24.25 in plus exact rear air clearance 2 in: 24.25 + 2 = 26.25 in. Calculation or inference: 24.25 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0 in | ✓ Verified — retained secondary source | Haier measurement source — 74843776.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceHaier measurement source — 74843776.pdf Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 0 inch minimum clearance at each side.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 0 inch minimum clearance at each side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0 in | ✓ Verified — retained secondary source | Haier measurement source — 74843776.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceHaier measurement source — 74843776.pdf Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 0 inch minimum clearance at each side.Open original source ↗ Why this value was usedLegacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 0 inch minimum clearance at each side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source | Haier measurement source — 74843777.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 74843777.pdf Exact-model manufacturer technical sheet specifies Top Air Clearance 0 in.Open original source ↗ Why this value was usedExact-model manufacturer technical sheet specifies Top Air Clearance 0 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Haier measurement source — 74843777.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceHaier measurement source — 74843777.pdf Exact-model manufacturer technical sheet specifies Back Air Clearance 2 in.Open original source ↗ Why this value was usedExact-model manufacturer technical sheet specifies Back Air Clearance 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 0.9375 in | ✓ Verified — retained secondary source · Calculated/inferred | Haier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS assets.skulytics.io | Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact | |
Value used by ExactFit0.9375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (29.625 - 27.75) / 2 Confidence label: high. Primary evidenceHaier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS Migrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact Haier width open 90 degrees is 29.625 in and closed width is 27.75 in; exact per-side operating envelope is (29.625 - 27.75) / 2 = 0.9375 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Symmetric multi-door family: current exact Haier width open 90 degrees is 29.625 in and closed width is 27.75 in; exact per-side operating envelope is (29.625 - 27.75) / 2 = 0.9375 in. Calculation or inference: (29.625 - 27.75) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 27.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Haier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS Haier | Retained specification excerpt: QJS15HY dimensional drawing spans the cabinet at the published overall width; current exact-model of | |
Value used by ExactFit27.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in Confidence label: high. Calculation inputs: Overall width; Primary evidenceHaier measurement source — 14-5-Cu-Ft-4-Door-Refrigerator-QJS15HYRFS QJS15HY dimensional drawing spans the cabinet at the published overall width; current exact-model official closed width is 27.75 in, so case width is 27.75 in.Open original source ↗ Why this value was usedQJS15HY dimensional drawing spans the cabinet at the published overall width; current exact-model official closed width is 27.75 in, so case width is 27.75 in. Calculation or inference: case_width_in = width_doors_closed_in. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 27.75 in. Earlier retained values: 27.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitSelected: 69.875 in. Earlier retained values: 69.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current exact-model Haier official weights and dimensions specification.
View source scope, location, and impact on fitSelected: 27.75 in. Earlier retained values: 27.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
QJS15HY dimensional drawing spans the cabinet at the published overall width; current exact-model official closed width is 27.75 in, so case width is 27.75 in. Calculation or inference: case_width_in = width_doors_closed_in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Haier · Web source · exact model/source
Model numbers covered: QJS15HYRFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
7 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Haier · Web source · exact model/source
Model numbers covered: QJS15HYRFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: QJS15HYRFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Specification sheet · secondary model/source
Model numbers covered: QJS15HYRFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.