Measurement evidence for GE Profile PXD22BYPFS

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to GE Profile PXD22BYPFS fit check Check this model against your opening How ExactFit verifies measurements

GE Profile PXD22BYPFS

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

5exact-model manufacturer values

0verified equivalent/same-chassis values

10secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-09-17. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.625 in	✓ Verified — exact model	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Overall Width = 35.625 in \| alue\":\"69.875 in\"},{\"id\":\"12671957\",\"name\":\"Spec_WEIGHTS & DIM
Value used by ExactFit 35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Overall Width = 35.625 in \| alue\":\"69.875 in\"},{\"id\":\"12671957\",\"name\":\"Spec_WEIGHTS & DIM Reviewed: 2026-09-04 Overall Width = 35.625 in \| alue\":\"69.875 in\"},{\"id\":\"12671957\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Width\",\"value\":\"35.625 in\"},{\"id\":\"12671958\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Side Air Clearance Open original source ↗ Why this value was used Overall Width = 35.625 in \| alue\":\"69.875 in\"},{\"id\":\"12671957\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Width\",\"value\":\"35.625 in\"},{\"id\":\"12671958\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Side Air Clearance Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.625 in	✓ Verified — retained secondary source	GE Profile installation document — 95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 95968936.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 C - Height to top of case (in) -> 68 5/8 Open original source ↗ Why this value was used C - Height to top of case (in) -> 68 5/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.75 in	✓ Verified — retained secondary source	GE Profile installation document — 95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 95968936.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 B - Height to top of hinge cover (in) -> 69 3/4 Open original source ↗ Why this value was used B - Height to top of hinge cover (in) -> 69 3/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.5 in	✓ Conflicting sources — resolved	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Official exact-model page: Case Depth Without Door 24.5 in; prior value was depth without handle.
Value used by ExactFit 24.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model page: Case Depth Without Door 24.5 in; prior value was depth without handle. Reviewed: 2026-09-04 Official exact-model page: Case Depth Without Door 24.5 in; prior value was depth without handle. Open original source ↗ Why this value was used Official exact-model page: Case Depth Without Door 24.5 in; prior value was depth without handle. Other evidence found 28.875 in — superseded Document 95968936.pdf; page 1. Model scope: not separately recorded. Raw value: F - Case Depth without Door Handle (in) -> 28 7/8. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	28.875 in	✓ Verified — exact model	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Depth Without Handle\",\"value\":\"28.875 in
Value used by ExactFit 28.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Without Handle\",\"value\":\"28.875 in Reviewed: 2026-09-04 Depth Without Handle\",\"value\":\"28.875 in Open original source ↗ Why this value was used Depth Without Handle\",\"value\":\"28.875 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31.25 in	✓ Verified — retained secondary source	GE Profile installation document — 95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 31.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 95968936.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 G - Overall Case Depth with Door Handle (in) -> 31 1/4 Open original source ↗ Why this value was used G - Overall Case Depth with Door Handle (in) -> 31 1/4 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	43 in	✓ Verified — retained secondary source	GE Profile installation document — 95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 43 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 95968936.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 H - Depth with Door open 90 deg (in) -> 43 Open original source ↗ Why this value was used H - Depth with Door open 90 deg (in) -> 43 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Conflicting sources — resolved	GE Profile measurement source — PXD22BYPFS-95968937.pdf assets.skulytics.io	Page 1
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968937.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact GE Profile PJD/PXD anti-tip installation guide visually states that cabinet opening width W should not be less than 36 in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PXD22BYPFS www.geappliances.com ↗ · Supporting model: PXD22BYPFS Why this value was used Exact GE Profile PJD/PXD anti-tip installation guide visually states that cabinet opening width W should not be less than 36 in. Other evidence found 35.875 in — superseded www.geappliances.com; location not retained. Model scope: not separately recorded. Raw value: Official Overall Width and Side Air Clearances; max(case_width_in,width_doors_closed_in) + 2 * side_clearance_wall_in = 35.875 in. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ 35.875 in — superseded www.geappliances.com; location not retained. Model scope: not separately recorded. Raw value: Official Overall Width and Side Air Clearances; max(case_width_in,width_doors_closed_in) + 2 * side_clearance_wall_in = 35.875 in. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.875 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 70.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 69.875 + 1 Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model sheet visually prints the tallest door endpoint 69.875 in and exact retained installation manual prints 1 in top clearance; opening height is 69.875 + 1 = 70.875 in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PXD22BYPFS www.geappliances.com ↗ · Supporting model: PXD22BYPFS Why this value was used Exact-model sheet visually prints the tallest door endpoint 69.875 in and exact retained installation manual prints 1 in top clearance; opening height is 69.875 + 1 = 70.875 in. Calculation or inference: 69.875 + 1. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	26.5 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 26.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.5 + 2 Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model sheet visually prints 24.5 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 24.5 + 2 = 26.5 in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PXD22BYPFS www.geappliances.com ↗ · Supporting model: PXD22BYPFS Why this value was used Exact-model sheet visually prints 24.5 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 24.5 + 2 = 26.5 in. Calculation or inference: 24.5 + 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.125 in	✓ Verified — exact model	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in Reviewed: 2026-09-05 Side Air Clearances\",\"value\":\"1/8 in Open original source ↗ Why this value was used Side Air Clearances\",\"value\":\"1/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.125 in	✓ Verified — exact model	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in Reviewed: 2026-09-05 Side Air Clearances\",\"value\":\"1/8 in Open original source ↗ Why this value was used Side Air Clearances\",\"value\":\"1/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	1 in	✓ Verified — retained secondary source	GE Profile measurement source — PXD22BYPFS-95968938.pdf assets.skulytics.io	Page 24
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968938.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-09-11 Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PXD22BYPFS www.geappliances.com ↗ · Supporting model: PXD22BYPFS Why this value was used Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	✓ Verified — exact model	GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile	Retained specification excerpt: Back Air Clearances\",\"value\":\"2 in
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS GE Profile · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Back Air Clearances\",\"value\":\"2 in Reviewed: 2026-09-05 Back Air Clearances\",\"value\":\"2 in Open original source ↗ Why this value was used Back Air Clearances\",\"value\":\"2 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	4.625 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 4.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (44.875 - 35.625) / 2 Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding. Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding. Calculation or inference: (44.875 - 35.625) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.625 in	✓ Verified — retained secondary source	GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PXD22BYPFS-95968936.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model GE Profile dimension sheet visually prints 35.625 in for case_width_in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PXD22BYPFS www.handlersappliance.com ↗ · Supporting model: PXD22BYPFS Why this value was used Exact-model GE Profile dimension sheet visually prints 35.625 in for case_width_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Depth without door

Selected: 24.5 in. Earlier retained values: 28.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Official exact-model page: Case Depth Without Door 24.5 in; prior value was depth without handle.

View source scope, location, and impact on fit

Minimum cutout width

Selected: 36 in. Earlier retained values: 35.875 in, 35.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact GE Profile PJD/PXD anti-tip installation guide visually states that cabinet opening width W should not be less than 36 in.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

GE Profile measurement source — GE-Profile-22-4-Cu-Ft-Smart-Counter-Depth-Fingerprint-Resistant-4-Door-French-Door-Refrigerator-with-Door-In-Door-PXD22BYPFS

GE Profile · Web source · exact model/source

Model numbers covered: PXD22BYPFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

6 displayed measurements supported: Overall width; Depth without door; Depth with door, without handles; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance.