This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-29. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-27-9-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-with-Kitchen-Assistant-PVD28HYYFS GE Profile | Retained specification excerpt: Overall Width = 35.625 in | alue\":\"69.875 in\"},{\"id\":\"13968915\",\"name\":\"Spec_WEIGHTS & DIM | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-27-9-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-with-Kitchen-Assistant-PVD28HYYFS Overall Width = 35.625 in | alue\":\"69.875 in\"},{\"id\":\"13968915\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Width\",\"value\":\"35.625 in\"},{\"id\":\"13968916\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Side Air ClearanceOpen original source ↗ Why this value was usedOverall Width = 35.625 in | alue\":\"69.875 in\"},{\"id\":\"13968915\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Width\",\"value\":\"35.625 in\"},{\"id\":\"13968916\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Side Air Clearance Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — retained secondary source | GE Profile installation document — 106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 106164969.pdf C - Height to top of case (in) -> 68 5/8Open original source ↗ Why this value was usedC - Height to top of case (in) -> 68 5/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.75 in | ✓ Verified — retained secondary source | GE Profile installation document — 106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 106164969.pdf B - Height to top of hinge cover (in) -> 69 3/4Open original source ↗ Why this value was usedB - Height to top of hinge cover (in) -> 69 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29 in | ✓ Conflicting sources — resolved | GE Profile measurement source — 106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — 106164969.pdf Exact PVD28 table: case depth without door 29 in; 34 1/4 in is not case-only depth.Open original source ↗ Why this value was usedExact PVD28 table: case depth without door 29 in; 34 1/4 in is not case-only depth. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.25 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-27-9-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-with-Kitchen-Assistant-PVD28HYYFS GE Profile | Retained specification excerpt: Depth Without Handle = 34.25 in | "value\":\"29.5 in\"},{\"id\":\"13968907\",\"name\":\"Spec_WEIGHTS | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-27-9-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-with-Kitchen-Assistant-PVD28HYYFS Depth Without Handle = 34.25 in | "value\":\"29.5 in\"},{\"id\":\"13968907\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Depth Without Handle\",\"value\":\"34.25 in\"},{\"id\":\"13968908\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Depth with Door OpOpen original source ↗ Why this value was usedDepth Without Handle = 34.25 in | "value\":\"29.5 in\"},{\"id\":\"13968907\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Depth Without Handle\",\"value\":\"34.25 in\"},{\"id\":\"13968908\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Depth with Door Op Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36.75 in | ✓ Verified — retained secondary source | GE Profile installation document — 106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 106164969.pdf G - Overall Case Depth with Door Handle (in) -> 36 3/4Open original source ↗ Why this value was usedG - Overall Case Depth with Door Handle (in) -> 36 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.375 in | ✓ Verified — retained secondary source | GE Profile measurement source — PVD28HYYFS-106164969.pdf appliancewarehouses.com | Page 1 | |
Value used by ExactFit48.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164969.pdf Exact-model GE Profile dimension sheet visually prints 48.375 in for depth_doors_open_90_in.Open original source ↗ All retained supporting links
Why this value was usedExact-model GE Profile dimension sheet visually prints 48.375 in for depth_doors_open_90_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.875 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PVD28HYYFS-106164968.pdf appliancehomestore.com | Page 24 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.625 + 2 * 0.125 Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164968.pdf Exact-model sheet prints 35.625 in widest closed width and exact installation manual prints 1/8 in each side; installation width is 35.625 + 2 * 0.125 = 35.875 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet prints 35.625 in widest closed width and exact installation manual prints 1/8 in each side; installation width is 35.625 + 2 * 0.125 = 35.875 in. Calculation or inference: 35.625 + 2 * 0.125. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PVD28HYYFS-106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 70 + 1 Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164969.pdf Exact-model sheet visually prints the tallest door endpoint 70 in and exact retained installation manual prints 1 in top clearance; opening height is 70 + 1 = 71 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet visually prints the tallest door endpoint 70 in and exact retained installation manual prints 1 in top clearance; opening height is 70 + 1 = 71 in. Calculation or inference: 70 + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PVD28HYYFS-106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit31 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29 + 2 Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164969.pdf Exact-model sheet visually prints 29 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 29 + 2 = 31 in.Open original source ↗ Why this value was usedExact-model sheet visually prints 29 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 29 + 2 = 31 in. Calculation or inference: 29 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | GE Profile measurement source — PVD28HYYFS-106164968.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164968.pdf Exact-model GE Profile installation manual prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model GE Profile installation manual prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | GE Profile measurement source — PVD28HYYFS-106164968.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164968.pdf Exact-model GE Profile installation manual prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model GE Profile installation manual prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | GE Profile measurement source — PVD28HYYFS-106164968.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164968.pdf Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | GE Profile measurement source — PVD28HYYFS-106164968.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164968.pdf Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.625 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PVD28HYYFS-106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit4.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (44.875 - 35.625) / 2 Confidence label: high. Primary evidenceGE Profile measurement source — PVD28HYYFS-106164969.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding. Calculation or inference: (44.875 - 35.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.375 in | ✓ Conflicting sources — resolved | GE Profile measurement source — 106164969.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.375 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — 106164969.pdf Exact PVD28 table: case width 35 3/8 in.Open original source ↗ Why this value was usedExact PVD28 table: case width 35 3/8 in. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 29 in. Earlier retained values: 34.25 in, 29.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact PVD28 table: case depth without door 29 in; 34 1/4 in is not case-only depth.
View source scope, location, and impact on fitSelected: 35.375 in. Earlier retained values: 35.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact PVD28 table: case width 35 3/8 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
GE Profile · Web source · exact model/source
Model numbers covered: PVD28HYYFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Overall width; Depth with door, without handles.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PVD28HYYFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
5 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth without door; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PVD28HYYFS. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
4 displayed measurements supported: Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PVD28HYYFS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
5 displayed measurements supported: Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.