Measurement evidence for GE Profile PSB48YSNSS

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to GE Profile PSB48YSNSS fit check Check this model against your opening How ExactFit verifies measurements

GE Profile PSB48YSNSS

Side-by-Side · Built-in
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

0verified equivalent/same-chassis values

15secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-09-17. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	48 in	✓ Conflicting sources — resolved	GE Profile installation document — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 48 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166431.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width: 48 in; 52 3/8 in is depth with door open 90 degrees. Open original source ↗ Why this value was used Width: 48 in; 52 3/8 in is depth with door open 90 degrees. Other evidence found 52.375 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Width (in.) G -> 52-3/8. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	83.5 in	✓ Conflicting sources — resolved	GE Profile installation document — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166431.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height to top of case: 83 1/2 in; height to top of grille: 84 in. Open original source ↗ Why this value was used Height to top of case: 83 1/2 in; height to top of grille: 84 in. Other evidence found 84 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Height to top of case (in.) B -> 84. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	84 in	✓ Verified — retained secondary source	GE Profile measurement source — PSB48YSNSS-105166431.pdf appliancewarehouses.com	Page 1
Value used by ExactFit 84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166431.pdf appliancewarehouses.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model GE Profile dimension sheet visually prints 84 in for height_hinge_in. Open original source ↗ All retained supporting links appliancewarehouses.com ↗ · Supporting model: PSB48YSNSS assets.skulytics.io ↗ · Supporting model: PSB48YSNSS Why this value was used Exact-model GE Profile dimension sheet visually prints 84 in for height_hinge_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	23.5 in	✓ Verified — retained secondary source	GE Profile installation document — 105166430.pdf (p.1) assets.skulytics.io	Page 1
Value used by ExactFit 23.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166430.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case depth without door (in.) C -> 23-1/2 Open original source ↗ Why this value was used Case depth without door (in.) C -> 23-1/2 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	25.75 in	✓ Conflicting sources — resolved	GE Profile installation document — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 25.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166431.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth without handle: 25 3/4 in; case depth without door: 23 1/2 in. Open original source ↗ Why this value was used Depth without handle: 25 3/4 in; case depth without door: 23 1/2 in. Other evidence found 23.5 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Case depth less door handle (in.) D -> 23-1/2. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	28.375 in	✓ Conflicting sources — resolved	GE Profile installation document — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 28.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166431.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth including handles: 28 3/8 in. Open original source ↗ Why this value was used Depth including handles: 28 3/8 in. Other evidence found 25.75 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Case depth with door handle (in.) E -> 25-3/4. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	52.375 in	✓ Conflicting sources — resolved	GE Profile installation document — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 52.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile installation document — 105166431.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth with fresh-food door open 90 degrees: 52 3/8 in. Open original source ↗ Why this value was used Depth with fresh-food door open 90 degrees: 52 3/8 in. Other evidence found 28.375 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with fresh food door open 90˚ (in.) F -> 28-3/8. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	47.5 in	✓ Verified — retained secondary source	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 47.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-07 Finished cutout width must be 47-1/2" for 48" models. Open original source ↗ Why this value was used Finished cutout width must be 47-1/2" for 48" models. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	83.5 in	✓ Verified — retained secondary source	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-07 Finished opening is adjustable around the 84" shipping height; exact case height is 83-1/2". Open original source ↗ Why this value was used Finished opening is adjustable around the 84" shipping height; exact case height is 83-1/2". Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	24 in	✓ Verified — retained secondary source	GE Profile measurement source — 105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — 105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-05 and the cold water supply located as shown. \| The Cutout Depth Must Be 24" (60.96 cm) \| The refrigerator will project forward, slightly beyond Open original source ↗ Why this value was used and the cold water supply located as shown. \| The Cutout Depth Must Be 24" (60.96 cm) \| The refrigerator will project forward, slightly beyond Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.25 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (47.5 - 47) / 2 Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-11 Exact installation page visually prints 47.5 in finished opening and 47 in case width; centered per-side cavity residual is (47.5 - 47) / 2 = 0.25 in. Open original source ↗ Why this value was used Exact installation page visually prints 47.5 in finished opening and 47 in case width; centered per-side cavity residual is (47.5 - 47) / 2 = 0.25 in. Calculation or inference: (47.5 - 47) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.25 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (47.5 - 47) / 2 Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-11 Exact installation page visually prints 47.5 in finished opening and 47 in case width; centered per-side cavity residual is (47.5 - 47) / 2 = 0.25 in. Open original source ↗ Why this value was used Exact installation page visually prints 47.5 in finished opening and 47 in case width; centered per-side cavity residual is (47.5 - 47) / 2 = 0.25 in. Calculation or inference: (47.5 - 47) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 23
Value used by ExactFit 0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 83.5 - 83.5 Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 23 Reviewed: 2026-09-11 Exact minimum opening height 83.5 in minus exact rear case height 83.5 in gives zero separate top residual at the minimum adjustable branch. Open original source ↗ Why this value was used Exact minimum opening height 83.5 in minus exact rear case height 83.5 in gives zero separate top residual at the minimum adjustable branch. Calculation or inference: 83.5 - 83.5. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	0.5 in	✓ Verified — retained secondary source · Calculated/inferred	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 24
Value used by ExactFit 0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 - 23.5 Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-09-11 Exact 24 in cutout depth minus exact 23.5 in case depth gives 0.5 in rear residual for the documented built-in branch. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: PSB48YSNSS images.salsify.com ↗ · Supporting model: PSB48YSNSS Why this value was used Exact 24 in cutout depth minus exact 23.5 in case depth gives 0.5 in rear residual for the documented built-in branch. Calculation or inference: 24 - 23.5. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	4.625 in	✓ Verified — retained secondary source	GE Profile measurement source — 105166431.pdf assets.skulytics.io	Page 1
Value used by ExactFit 4.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidence GE Profile measurement source — 105166431.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Exact product-clearance table: 4 5/8 in minimum at the 90-degree door stop; larger asymmetric 130-degree values remain in the evidence. Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Exact product-clearance table: 4 5/8 in minimum at the 90-degree door stop; larger asymmetric 130-degree values remain in the evidence. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	47 in	✓ Conflicting sources — resolved	GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io	Page 24
Value used by ExactFit 47 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE Profile measurement source — PSB48YSNSS-105166429.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-09-07 Exact installation drawing: 47" Case Width; 48" is Frame to Frame. Open original source ↗ Why this value was used Exact installation drawing: 47" Case Width; 48" is Frame to Frame. Other evidence found 52.375 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Width (in.) G -> 52-3/8. The final reviewed registry supersedes this earlier audit value. 48 in — superseded Document 105166431.pdf; page 1. Model scope: not separately recorded. Raw value: Width: 48 in; 52 3/8 in is depth with door open 90 degrees.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Overall width

Selected: 48 in. Earlier retained values: 52.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Width: 48 in; 52 3/8 in is depth with door open 90 degrees.

View source scope, location, and impact on fit

Cabinet height

Selected: 83.5 in. Earlier retained values: 84 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Height to top of case: 83 1/2 in; height to top of grille: 84 in.

View source scope, location, and impact on fit

Depth with door, without handles

Selected: 25.75 in. Earlier retained values: 23.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth without handle: 25 3/4 in; case depth without door: 23 1/2 in.

View source scope, location, and impact on fit

Depth with handle

Selected: 28.375 in. Earlier retained values: 25.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth including handles: 28 3/8 in.

View source scope, location, and impact on fit

Depth with doors open at 90°

Selected: 52.375 in. Earlier retained values: 28.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth with fresh-food door open 90 degrees: 52 3/8 in.

View source scope, location, and impact on fit

Cabinet case width

Selected: 47 in. Earlier retained values: 52.375 in, 48 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact installation drawing: 47" Case Width; 48" is Frame to Frame.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

GE Profile measurement source — 105166431.pdf

assets.skulytics.io · Web source · secondary model/source

Model numbers covered: PSB48YSNSS. Publication/revision date: Not recorded. Reviewed: 2026-09-17.

6 displayed measurements supported: Overall width; Cabinet height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°.