This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-03. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Overall Width\",\"value\":\"35.625 in | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Overall Width\",\"value\":\"35.625 inOpen original source ↗ Why this value was usedOverall Width\",\"value\":\"35.625 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — retained secondary source | GE Profile installation document — 104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 104315088.pdf C Height to top of case (in) -> 68 5/8Open original source ↗ Why this value was usedC Height to top of case (in) -> 68 5/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Conflicting sources — resolved | GE Profile measurement source — 104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — 104315088.pdf Overall height to the top of the door 69-7/8 in; the same table prints Height to top of hinge 69-3/4. The stored field holds the appliance's highest point (owner decision, as for the GE three-row tables).Open original source ↗ Why this value was usedOverall height to the top of the door 69-7/8 in; the same table prints Height to top of hinge 69-3/4. The stored field holds the appliance's highest point (owner decision, as for the GE three-row tables). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.5 in | ✓ Conflicting sources — resolved | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Official exact-model page: Case Depth Without Door 29.5 in; prior value was depth without handle. | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Official exact-model page: Case Depth Without Door 29.5 in; prior value was depth without handle.Open original source ↗ Why this value was usedOfficial exact-model page: Case Depth Without Door 29.5 in; prior value was depth without handle. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.25 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Depth Without Handle\",\"value\":\"34.25 in | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Depth Without Handle\",\"value\":\"34.25 inOpen original source ↗ Why this value was usedDepth Without Handle\",\"value\":\"34.25 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36.75 in | ✓ Verified — retained secondary source | GE Profile installation document — 104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 104315088.pdf G Overall Case Depth with Door Handle (in) -> 36 3/4Open original source ↗ Why this value was usedG Overall Case Depth with Door Handle (in) -> 36 3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.375 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Depth with Door Open 90°\",\"value\":\"48.375 in | |
Value used by ExactFit48.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Depth with Door Open 90°\",\"value\":\"48.375 inOpen original source ↗ Why this value was usedDepth with Door Open 90°\",\"value\":\"48.375 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.875 in | ✓ Conflicting sources — resolved · Calculated/inferred | GE Profile measurement source — PAD28BYTFS_104315090.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.625 + 2 * 0.125 Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315090.pdf Exact-model sheet prints 35.625 in widest closed width and exact installation manual prints 1/8 in each side; installation width is 35.625 + 2 * 0.125 = 35.875 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet prints 35.625 in widest closed width and exact installation manual prints 1/8 in each side; installation width is 35.625 + 2 * 0.125 = 35.875 in. Calculation or inference: 35.625 + 2 * 0.125. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.875 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PAD28BYTFS_104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 69.875 + 1 Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315088.pdf Exact-model sheet visually prints the tallest door endpoint 69.875 in and exact retained installation manual prints 1 in top clearance; opening height is 69.875 + 1 = 70.875 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet visually prints the tallest door endpoint 69.875 in and exact retained installation manual prints 1 in top clearance; opening height is 69.875 + 1 = 70.875 in. Calculation or inference: 69.875 + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.5 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PAD28BYTFS_104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315088.pdf Exact-model sheet visually prints 29.5 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 29.5 + 2 = 31.5 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet visually prints 29.5 in case-only depth and exact retained installation manual prints 2 in back clearance; installation depth is 29.5 + 2 = 31.5 in. Calculation or inference: 29.5 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Side Air Clearances\",\"value\":\"1/8 inOpen original source ↗ Why this value was usedSide Air Clearances\",\"value\":\"1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | GE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS GE Profile | Retained specification excerpt: Side Air Clearances\",\"value\":\"1/8 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — GE-Profile-ENERGY-STAR-28-4-Cu-Ft-Quad-Door-Refrigerator-with-Dual-Dispense-AutoFill-Pitcher-and-Door-in-Door-PAD28BYTFS Side Air Clearances\",\"value\":\"1/8 inOpen original source ↗ Why this value was usedSide Air Clearances\",\"value\":\"1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | GE Profile measurement source — PAD28BYTFS_104315090.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315090.pdf Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | GE Profile measurement source — PAD28BYTFS_104315090.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315090.pdf Exact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model retained GE Profile installation manual visually prints clearances: Sides 1/8 in, Top 1 in, Back 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.625 in | ✓ Verified — retained secondary source · Calculated/inferred | GE Profile measurement source — PAD28BYTFS_104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit4.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (44.875 - 35.625) / 2 Confidence label: high. Primary evidenceGE Profile measurement source — PAD28BYTFS_104315088.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model sheet visually shows symmetric doors, 44.875 in width open 90 degrees including handles, and 35.625 in closed width; exact per-side operating envelope is (44.875 - 35.625) / 2 = 4.625 in with no rounding. Calculation or inference: (44.875 - 35.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | GE Profile installation document — 104315088.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE Profile installation document — 104315088.pdf J Case Width (in) = 35 5/8"Open original source ↗ Why this value was usedJ Case Width (in) = 35 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69.875 in. Earlier retained values: 69.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Overall height to the top of the door 69-7/8 in; the same table prints Height to top of hinge 69-3/4. The stored field holds the appliance's highest point (owner decision, as for the GE three-row tables).
View source scope, location, and impact on fitSelected: 29.5 in. Earlier retained values: 34.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official exact-model page: Case Depth Without Door 29.5 in; prior value was depth without handle.
View source scope, location, and impact on fitSelected: 35.875 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model sheet prints 35.625 in widest closed width and exact installation manual prints 1/8 in each side; installation width is 35.625 + 2 * 0.125 = 35.875 in. Calculation or inference: 35.625 + 2 * 0.125.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
GE Profile · Web source · exact model/source
Model numbers covered: PAD28BYTFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
6 displayed measurements supported: Overall width; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: PAD28BYTFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PAD28BYTFS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
3 displayed measurements supported: Minimum cutout width; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PAD28BYTFS. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
3 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-03. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.