Measurement evidence for GE GZS24NMYES

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to GE GZS24NMYES fit check Check this model against your opening How ExactFit verifies measurements

GE GZS24NMYES

Side-by-Side · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

0verified equivalent/same-chassis values

13secondary-source-only values

3values with unresolved source details

Last reviewed: 2026-09-17. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.75 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Open original source ↗ Why this value was used Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.9375 in	✓ Conflicting sources — resolved	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 68.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Popular-brand audit: exact endpoint for height_case_in is 68.9375 in; replaces 69.9375 in. Open original source ↗ Why this value was used Popular-brand audit: exact endpoint for height_case_in is 68.9375 in; replaces 69.9375 in. Other evidence found 69.9375 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8". The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.9375 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 69.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Open original source ↗ Why this value was used Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	25.0625 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf (p.1) assets.skulytics.io	Page 1
Value used by ExactFit 25.0625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case depth without doors, without handles (C) -> 25-1/16 Open original source ↗ Why this value was used Case depth without doors, without handles (C) -> 25-1/16 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	29.625 in	✓ Conflicting sources — resolved	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 29.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Popular-brand audit: exact endpoint for depth_less_handles_in is 29.625 in; replaces 31.625 in. Open original source ↗ Why this value was used Popular-brand audit: exact endpoint for depth_less_handles_in is 29.625 in; replaces 31.625 in. Other evidence found 31.625 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8". The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31.625 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 31.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Open original source ↗ Why this value was used Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	46.875 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf (p.1) assets.skulytics.io	Page 1
Value used by ExactFit 46.875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf (p.1) assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Total depth with fresh food door open 90° (I) -> 46-7/8 Open original source ↗ Why this value was used Total depth with fresh food door open 90° (I) -> 46-7/8 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Verified — retained secondary source · Calculated/inferred	GE measurement source — 106298023.pdf assets.skulytics.io	Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, si
Value used by ExactFit 36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidence GE measurement source — 106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, si Reviewed: 2026-09-09 GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in. Open original source ↗ Why this value was used GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.9375 in	✓ Verified — retained secondary source · Calculated/inferred	GE measurement source — GZS24NMYES-106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 70.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 69.9375 + 1 Confidence label: high. Primary evidence GE measurement source — GZS24NMYES-106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model GE source visually prints the tallest appliance endpoint as 69.9375 in and specifies 1 in top clearance; required opening height is 69.9375 + 1 = 70.9375 in. The tallest door/overall endpoint controls rather than the lower hinge endpoint. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: GZS24NMYES www.weaverappliance.com ↗ · Supporting model: GZS24NMYES Why this value was used Exact-model GE source visually prints the tallest appliance endpoint as 69.9375 in and specifies 1 in top clearance; required opening height is 69.9375 + 1 = 70.9375 in. The tallest door/overall endpoint controls rather than the lower hinge endpoint. Calculation or inference: 69.9375 + 1. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	27.0625 in	? Verified — finalized database measurement · Calculated/inferred	GE measurement source — 106298023.pdf (p.1) + GE-GZS24NMYES-GE-23-6-Cu-Ft-Counter-Depth-Side-By-Side-Refrigerator-with-Extra-Tall-Dispenser-and-In-Door-Icemaker www.weaverappliance.com	Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=25.0
Value used by ExactFit 27.0625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidence GE measurement source — 106298023.pdf (p.1) + GE-GZS24NMYES-GE-23-6-Cu-Ft-Counter-Depth-Side-By-Side-Refrigerator-with-Extra-Tall-Dispenser-and-In-Door-Icemaker www.weaverappliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=25.0 Reviewed: 2026-09-09 GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=25.0625, rear_clearance_in=2; result=27.0625 in. Open original source ↗ Why this value was used GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=25.0625, rear_clearance_in=2; result=27.0625 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.125 in	✓ Verified — retained secondary source	GE measurement source — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE measurement source — 106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Air Clearances table states Each side: 0.125 in. Open original source ↗ Why this value was used Air Clearances table states Each side: 0.125 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.125 in	✓ Verified — retained secondary source	GE measurement source — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE measurement source — 106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Air Clearances table states Each side: 0.125 in. Open original source ↗ Why this value was used Air Clearances table states Each side: 0.125 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	1 in	✓ Verified — retained secondary source	GE measurement source — GZS24NMYES-106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE measurement source — GZS24NMYES-106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-11 Exact-model GE specification/Quick Specs lists Top Air Clearance as 1 in. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: GZS24NMYES www.weaverappliance.com ↗ · Supporting model: GZS24NMYES Why this value was used Exact-model GE specification/Quick Specs lists Top Air Clearance as 1 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	? Verified — finalized database measurement	GE measurement source — GE-GZS24NMYES-GE-23-6-Cu-Ft-Counter-Depth-Side-By-Side-Refrigerator-with-Extra-Tall-Dispenser-and-In-Door-Icemaker www.weaverappliance.com	Retained specification excerpt: Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 dom
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE measurement source — GE-GZS24NMYES-GE-23-6-Cu-Ft-Counter-Depth-Side-By-Side-Refrigerator-with-Extra-Tall-Dispenser-and-In-Door-Icemaker www.weaverappliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 dom Reviewed: 2026-09-05 Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 domains; official=False. Open original source ↗ Why this value was used Cached exact-model air-clearance specification: rear_clearance_in=2 in; 2 source copies across 2 domains; official=False. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	3.75 in	✓ Verified — retained secondary source	GE measurement source — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: max(freezer-side 90deg wall clearance, fresh-food-side 90deg wall clearance) Confidence label: high. Primary evidence GE measurement source — 106298023.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in. Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.75 in	✓ Verified — retained secondary source	GE installation document — 106298023.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence GE installation document — 106298023.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Open original source ↗ Why this value was used Dimensions (WxHxD) 35-3/4" x 69-15/16" x 31-5/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 68.9375 in. Earlier retained values: 69.9375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Popular-brand audit: exact endpoint for height_case_in is 68.9375 in; replaces 69.9375 in.

View source scope, location, and impact on fit

Depth with door, without handles

Selected: 29.625 in. Earlier retained values: 31.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Popular-brand audit: exact endpoint for depth_less_handles_in is 29.625 in; replaces 31.625 in.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

GE installation document — 106298023.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: GZS24NMYES. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for door open to 90°; Cabinet case width.