Measurement evidence for GE GWE19JYLFS

Value used by ExactFit

32.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width (in.) H -> 32-3/4

Why this value was used

Width (in.) H -> 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of case (in.) C -> 68-5/8

Why this value was used

Height to top of case (in.) C -> 68-5/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of hinge (in.) B -> 69-3/4

Why this value was used

Height to top of hinge (in.) B -> 69-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth without door (in.) D -> 24-1/8

Why this value was used

Case depth without door (in.) D -> 24-1/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth less door handle (in.) E -> 29

Why this value was used

Case depth less door handle (in.) E -> 29

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth with door handle (in.) F -> 31

Why this value was used

Case depth with door handle (in.) F -> 31

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

42 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with fresh food door open 90˚ (in.) G -> 42

Why this value was used

Depth with fresh food door open 90˚ (in.) G -> 42

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 32.75 + 2 * 0.125

Confidence label: medium.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Minimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Why this value was used

Minimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2 Calculation or inference: 32.75 + 2 * 0.125.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK
www.bandjappliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.75 in plus propagated top clearanc
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 69.75 in plus propagated top clearance 1.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 70.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ...
www.appliancealliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.125 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.125 in plus propagated rear clearance 2.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 26.125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Why this value was used

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Why this value was used

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model GE GYE18JYLFS

Confidence label: medium.

Primary evidence

GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK
www.bandjappliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to GE GYE18JYLFS; original evidence:
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to GE GYE18JYLFS; original evidence: Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 1 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Cafe CWE19SP3ND1

Confidence label: medium.

Primary evidence

CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ...
www.appliancealliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Cafe CWE19SP3ND1; original evidenc
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Cafe CWE19SP3ND1; original evidence: Exact-model cached page explicitly labels rear_clearance_in=2 in; 1 cached copy/copies; no contrary parsed value.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: ceil_to_1/8((width_open_90 - max(case_width,width_closed)) / 2)

Confidence label: medium.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model GE width-open geometry: width with door(s) open 90 degrees 40.5 in; widest closed appliance width 32.75 in; two-door per-side half-excess rounded upward to 1/8 in = 3.875 in. Table: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Why this value was used

Exact-model GE width-open geometry: width with door(s) open 90 degrees 40.5 in; widest closed appliance width 32.75 in; two-door per-side half-excess rounded upward to 1/8 in = 3.875 in. Table: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2 Calculation or inference: ceil_to_1/8((width_open_90 - max(case_width,width_closed)) / 2).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width (in.) H -> 32-3/4

Why this value was used

Width (in.) H -> 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE GWE19JYLFS Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Why this value was used

Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-3/4 | 68-5/8 | 24-1/8 | 29 | 31 | 42 | 32-3/4 | 40-1/2 | 1/8 | 1 | 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.