This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 28 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Width (in.) G -> 28Open original source ↗ Why this value was usedWidth (in.) G -> 28 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 61.25 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit61.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Height to top of case (in.) B -> 61-1/4Open original source ↗ Why this value was usedHeight to top of case (in.) B -> 61-1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 61.75 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit61.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Height to top of hinge (in.) A -> 61-3/4Open original source ↗ Why this value was usedHeight to top of hinge (in.) A -> 61-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 26.75 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit26.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Case depth without door (in.) C -> 26-3/4Open original source ↗ Why this value was usedCase depth without door (in.) C -> 26-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.5 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit30.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Case depth less door handle (in.) D -> 30-1/2Open original source ↗ Why this value was usedCase depth less door handle (in.) D -> 30-1/2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 32.625 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit32.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Case depth with door handle (in.) E -> 32-5/8Open original source ↗ Why this value was usedCase depth with door handle (in.) E -> 32-5/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 57 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit57 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Depth with fresh food door open 90˚ (in.) F -> 57Open original source ↗ Why this value was usedDepth with fresh food door open 90˚ (in.) F -> 57 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 29.5 in | ✓ Secondary source only · Calculated/inferred | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 28.0 + 2 * 0.75 Confidence label: medium. Primary evidenceGE GTE16DTNRWW Quick Specs Minimum opening derived from exact product width plus explicit symmetric side spacing: 28.0 + 2 * 0.75 = 29.5 in. Side evidence: Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedMinimum opening derived from exact product width plus explicit symmetric side spacing: 28.0 + 2 * 0.75 = 29.5 in. Side evidence: Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Calculation or inference: 28.0 + 2 * 0.75. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | Unknown | ? Not found · Calculated/inferred | GTE16DTNLWW GE® ENERGY STAR® 15.6 Cu. Ft. Top ... dshomeappliances.com | Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 61.75 in plus propagated top clearanc | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceGTE16DTNLWW GE® ENERGY STAR® 15.6 Cu. Ft. Top ... Minimum opening height derived from highest appliance endpoint 61.75 in plus propagated top clearance 1.0 in.Open original source ↗ Why this value was usedA required calculation input lacks defensible evidence. Retained research value: 62.75 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 27.75 in | ✓ Secondary source only · Calculated/inferred | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit27.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceGE GTE16DTNRWW Quick Specs Minimum opening depth = verified case-only depth 26.75 in + GE rear clearance 1 in.Open original source ↗ Why this value was usedMinimum opening depth = verified case-only depth 26.75 in + GE rear clearance 1 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.75 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.75 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | Unknown | ? Not found · Calculated/inferred | GTE16DTNLWW GE® ENERGY STAR® 15.6 Cu. Ft. Top ... dshomeappliances.com | Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to GE GTE16DTNLWW; original evidence: | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model GE GTE16DTNLWW Confidence label: medium. Primary evidenceGTE16DTNLWW GE® ENERGY STAR® 15.6 Cu. Ft. Top ... Conflict-free corporate-family exact 8-dimension chassis match to GE GTE16DTNLWW; original evidence: Cached exact-model air-clearance specification: top_clearance_in=1 in; 2 source copies across 2 domains; official=False.Open original source ↗ Why this value was usedThe stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 1 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 2.625 in | ✓ Secondary source only · Calculated/inferred | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit2.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: ceil_to_1/8(width_open_90 - max(case_width,width_closed)) Confidence label: medium. Primary evidenceGE GTE16DTNRWW Quick Specs Exact-model GE width-open geometry: width with door(s) open 90 degrees 30.625 in; widest closed appliance width 28 in; single-door side excess rounded upward to 1/8 in = 2.625 in. Table: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model GE width-open geometry: width with door(s) open 90 degrees 30.625 in; widest closed appliance width 28 in; single-door side excess rounded upward to 1/8 in = 2.625 in. Table: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Calculation or inference: ceil_to_1/8(width_open_90 - max(case_width,width_closed)). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 28 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Width (in.) G -> 28Open original source ↗ Why this value was usedWidth (in.) G -> 28 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.75 in | ✓ Secondary source only | GE GTE16DTNRWW Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GTE16DTNRWW Quick Specs Confirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedConfirmed from GE ordered dimensions/air-clearances table. GE ordered dimension table values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: https://dshomeappliances.com/products/ge-gte16dtnlww. Related-model record: GTE16DTNRWW.
A required calculation input lacks defensible evidence.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: https://dshomeappliances.com/products/ge-gte16dtnlww. Related-model record: GTE16DTNRWW.
The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: GTE16DTNRWW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
14 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: GTE16DTNRWW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗dshomeappliances.com · Web source · Scope not established
Model numbers covered: GTE16DTNRWW. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout height; Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.