This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 28 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Width (in.) G -> 28Open original source ↗ Why this value was usedWidth (in.) G -> 28 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 61.25 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit61.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Height to top of case (in.) B -> 61-1/4Open original source ↗ Why this value was usedHeight to top of case (in.) B -> 61-1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 61.75 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit61.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Height to top of hinge (in.) A -> 61-3/4Open original source ↗ Why this value was usedHeight to top of hinge (in.) A -> 61-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 26.75 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit26.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Case depth without door (in.) C -> 26-3/4Open original source ↗ Why this value was usedCase depth without door (in.) C -> 26-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.5 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit30.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Case depth less door handle (in.) D -> 30-1/2Open original source ↗ Why this value was usedCase depth less door handle (in.) D -> 30-1/2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 32.625 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Case depth with door handle (in.) E -> 32-5/8Open original source ↗ Why this value was usedCase depth with door handle (in.) E -> 32-5/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 57 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit57 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Depth with fresh food door open 90˚ (in.) F -> 57Open original source ↗ Why this value was usedDepth with fresh food door open 90˚ (in.) F -> 57 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 29.5 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 105174922.pdf + 105174922.pdf assets.skulytics.io | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=28, side_ | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceGE measurement source — 105174922.pdf + 105174922.pdf GE additive installation-envelope calculation from high-confidence operands: case_width_in=28, side_ventilation_clearance_in=0.75; result=29.5 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: case_width_in=28, side_ventilation_clearance_in=0.75; result=29.5 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 62.75 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 105174922.pdf + 105174922.pdf dshomeappliances.com | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=61.75, | |
Value used by ExactFit62.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceGE measurement source — 105174922.pdf + 105174922.pdf GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=61.75, top_clearance_in=1; result=62.75 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: height_hinge_in=61.75, top_clearance_in=1; result=62.75 in. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 27.75 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 105174922.pdf + 105174922.pdf assets.skulytics.io | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=26.7 | |
Value used by ExactFit27.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceGE measurement source — 105174922.pdf + 105174922.pdf GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=26.75, rear_clearance_in=1; result=27.75 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=26.75, rear_clearance_in=1; result=27.75 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.75 in | ✓ Verified — retained secondary source | GE measurement source — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 105174922.pdf Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.75 in | ✓ Verified — retained secondary source | GE measurement source — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 105174922.pdf Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | GE specification record — 105174922.pdf dshomeappliances.com | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE specification record — 105174922.pdf Visually reviewed exact-model GE Quick Specs ordered table. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1. Trailing labeled air-clearance trio: Each side=0.75, Top=1, Back=1 in.Open original source ↗ Why this value was usedVisually reviewed exact-model GE Quick Specs ordered table. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1. Trailing labeled air-clearance trio: Each side=0.75, Top=1, Back=1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | GE measurement source — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 105174922.pdf Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 61-3/4 | 61-1/4 | 26-3/4 | 30-1/2 | 32-5/8 | 57 | 28 | 30-5/8 | 3/4 | 1 | 1 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.625 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — GTE16DTNLWW-105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2.625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 30.625 - 28 Confidence label: high. Primary evidenceGE measurement source — GTE16DTNLWW-105174922.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE Quick Specs visually prints a single/reversible door, 30.625 in width open 90 degrees including handle, and 28 in closed width; exact hinge-side operating envelope is 30.625 - 28 = 2.625 in, with no safety rounding.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE Quick Specs visually prints a single/reversible door, 30.625 in width open 90 degrees including handle, and 28 in closed width; exact hinge-side operating envelope is 30.625 - 28 = 2.625 in, with no safety rounding. Calculation or inference: 30.625 - 28. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 28 in | ✓ Verified — retained secondary source | GE installation document — 105174922.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 105174922.pdf Width (in.) G -> 28Open original source ↗ Why this value was usedWidth (in.) G -> 28 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: GTE16DTNLWW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: GTE16DTNLWW. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
3 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: GTE16DTNLWW. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.