Measurement evidence for GE GSS28NMYES

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Why this value was used

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE labeled product-dimensions table: Height to top of case (B) = 68-15/16 in; the separate total WxHxD line is overall hinge height.

Why this value was used

Exact-model GE labeled product-dimensions table: Height to top of case (B) = 68-15/16 in; the separate total WxHxD line is overall hinge height.

Other evidence found

• 69.9375 in — superseded

  Document 106298040.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Why this value was used

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Case depth without doors, without handles (C) -> 29-7/16

Why this value was used

Case depth without doors, without handles (C) -> 29-7/16

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE labeled product-dimensions table: Depth with doors, without handles (D) = 34 in; the separate 36-in total depth includes handles.

Why this value was used

Exact-model GE labeled product-dimensions table: Depth with doors, without handles (D) = 34 in; the separate 36-in total depth includes handles.

Other evidence found

• 36 in — superseded

  Document 106298040.pdf; page 1. Model scope: not separately recorded. Raw value: Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Why this value was used

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

51.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf (p.2)
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Total depth with fresh food door open 90° (I) -> 51-1/4

Why this value was used

Total depth with fresh food door open 90° (I) -> 51-1/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

GE measurement source — 106298040.pdf + 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, si
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

GE measurement source — 106298040.pdf + 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375, top_clearance_in=1; result=70.9375 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375, top_clearance_in=1; result=70.9375 in. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

GE measurement source — 106298040.pdf (p.2) + 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4375, rear_clearance_in=2; result=31.4375 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4375, rear_clearance_in=2; result=31.4375 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE Air Clearances table: Each side = 0.125 in.

Why this value was used

Exact-model GE Air Clearances table: Each side = 0.125 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE Air Clearances table: Each side = 0.125 in.

Why this value was used

Exact-model GE Air Clearances table: Each side = 0.125 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE Air Clearances table: Top = 1 in.

Why this value was used

Exact-model GE Air Clearances table: Top = 1 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Exact-model GE Air Clearances table: Back = 2 in.

Why this value was used

Exact-model GE Air Clearances table: Back = 2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: max(freezer-side 90deg wall clearance, fresh-food-side 90deg wall clearance)

Confidence label: high.

Primary evidence

GE measurement source — 106298040.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in.

Why this value was used

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 106298040.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Why this value was used

Dimensions (WxHxD) 35-3/4" x 69-15/16" x 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.