This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE labeled product-dimensions table: Overall case width (G) = 35.75 in.Open original source ↗ Why this value was usedExact-model GE labeled product-dimensions table: Overall case width (G) = 35.75 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.9375 in | ✓ Verified — retained secondary source | GE installation document — 106298046.pdf (p.1) assets.skulytics.io | Page 1 | |
Value used by ExactFit68.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 106298046.pdf (p.1) Height to top of case (B) -> 68-15/16Open original source ↗ Why this value was usedHeight to top of case (B) -> 68-15/16 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.9375 in | ✓ Verified — retained secondary source | GE installation document — 106298046.pdf (p.1) assets.skulytics.io | Page 1 | |
Value used by ExactFit69.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 106298046.pdf (p.1) Height to top of hinge and door (A) -> 69-15/16Open original source ↗ Why this value was usedHeight to top of hinge and door (A) -> 69-15/16 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.4375 in | ✓ Verified — retained secondary source | GE installation document — 106298046.pdf (p.1) assets.skulytics.io | Page 1 | |
Value used by ExactFit29.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 106298046.pdf (p.1) Case depth without doors, without handles (C) -> 29-7/16Open original source ↗ Why this value was usedCase depth without doors, without handles (C) -> 29-7/16 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit34 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE labeled product-dimensions table: Depth with doors, without handles (D) = 34 in.Open original source ↗ Why this value was usedExact-model GE labeled product-dimensions table: Depth with doors, without handles (D) = 34 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit36 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE labeled product-dimensions table: Overall depth with doors and handles (E) = 36 in.Open original source ↗ Why this value was usedExact-model GE labeled product-dimensions table: Overall depth with doors and handles (E) = 36 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 51.25 in | ✓ Verified — retained secondary source | GE installation document — 106298046.pdf (p.1) assets.skulytics.io | Page 1 | |
Value used by ExactFit51.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE installation document — 106298046.pdf (p.1) Total depth with fresh food door open 90° (I) -> 51-1/4Open original source ↗ Why this value was usedTotal depth with fresh food door open 90° (I) -> 51-1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 106298048.pdf GE | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, si | |
Value used by ExactFit36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceGE measurement source — 106298048.pdf GE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: case_width_in=35.75, side_ventilation_clearance_in=0.125; result=36 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.9375 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 106298046.pdf (p.1) + 106298048.pdf www.ajmadison.com | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375 | |
Value used by ExactFit70.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceGE measurement source — 106298046.pdf (p.1) + 106298048.pdf GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375, top_clearance_in=1; result=70.9375 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.9375, top_clearance_in=1; result=70.9375 in. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.4375 in | ✓ Verified — retained secondary source · Calculated/inferred | GE measurement source — 106298046.pdf (p.1) + 106298048.pdf www.ajmadison.com | Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4 | |
Value used by ExactFit31.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceGE measurement source — 106298046.pdf (p.1) + 106298048.pdf GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4375, rear_clearance_in=2; result=31.4375 in.Open original source ↗ Why this value was usedGE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=29.4375, rear_clearance_in=2; result=31.4375 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | GE measurement source — 106298048.pdf GE | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE Air Clearances table: Each side = 0.125 in.Open original source ↗ Why this value was usedExact-model GE Air Clearances table: Each side = 0.125 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | GE measurement source — 106298048.pdf GE | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE Air Clearances table: Each side = 0.125 in.Open original source ↗ Why this value was usedExact-model GE Air Clearances table: Each side = 0.125 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE Air Clearances table: Top = 1 in.Open original source ↗ Why this value was usedExact-model GE Air Clearances table: Top = 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE Air Clearances table: Back = 2 in.Open original source ↗ Why this value was usedExact-model GE Air Clearances table: Back = 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.75 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: max(freezer-side 90deg wall clearance, fresh-food-side 90deg wall clearance) Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE table lists 90-degree adjacent-wall clearance for freezer side 3 11/16 in and fresh-food side 3 3/4 in; conservative either-side requirement is 3 3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | GE measurement source — 106298048.pdf www.ajmadison.com | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — 106298048.pdf Exact-model GE labeled product-dimensions table: Overall/Case Width (G) = 35-3/4 in.Open original source ↗ Why this value was usedExact-model GE labeled product-dimensions table: Overall/Case Width (G) = 35-3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
www.ajmadison.com · Web source · secondary model/source
Model numbers covered: GSE28NGYBB. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
10 displayed measurements supported: Overall width; Depth with door, without handles; Depth with handle; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: GSE28NGYBB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth without door; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.ajmadison.com · Web source · secondary model/source
Model numbers covered: GSE28NGYBB. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
2 displayed measurements supported: Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.