This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.75 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit32.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Width (in.) H -> 32-3/4Open original source ↗ Why this value was usedWidth (in.) H -> 32-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Height to top of case (in.) C -> 69Open original source ↗ Why this value was usedHeight to top of case (in.) C -> 69 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Conflicting sources — resolved | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Visual/native table repair: replaced legacy misassociated value 69.625 with labeled GE table value 69.875.Open original source ↗ Why this value was usedVisual/native table repair: replaced legacy misassociated value 69.625 with labeled GE table value 69.875. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28.5 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit28.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Case depth without door (in.) D -> 28-1/2Open original source ↗ Why this value was usedCase depth without door (in.) D -> 28-1/2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 32.75 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit32.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Case depth less door handle (in.) E -> 32-3/4Open original source ↗ Why this value was usedCase depth less door handle (in.) E -> 32-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 34.75 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit34.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Case depth with door handle (in.) F -> 34-3/4Open original source ↗ Why this value was usedCase depth with door handle (in.) F -> 34-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 50.5 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit50.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Depth with fresh food door open 90° (in.) G -> 50-1/2Open original source ↗ Why this value was usedDepth with fresh food door open 90° (in.) G -> 50-1/2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33 in | ✓ Secondary source only · Calculated/inferred | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 32.75 + 2 * 0.125 Confidence label: medium. Primary evidenceGE GSE23GYPFS Quick Specs Minimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2Open original source ↗ Why this value was usedMinimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2 Calculation or inference: 32.75 + 2 * 0.125. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.875 in | ✓ Secondary source only · Calculated/inferred | GSE23GYPFS (Refrigerators - Side-by-Side) www.qualityelectronicsonline.com | Retained specification excerpt: Minimum opening height = highest verified appliance height 69.875 in + GE top clearance 1 in. | |
Value used by ExactFit70.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceGSE23GYPFS (Refrigerators - Side-by-Side) Minimum opening height = highest verified appliance height 69.875 in + GE top clearance 1 in.Open original source ↗ Why this value was usedMinimum opening height = highest verified appliance height 69.875 in + GE top clearance 1 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.5 in | ✓ Secondary source only · Calculated/inferred | GSE23GYPFS (Refrigerators - Side-by-Side) www.qualityelectronicsonline.com | Retained specification excerpt: Minimum opening depth = verified case-only depth 28.5 in + GE rear clearance 2 in. | |
Value used by ExactFit30.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceGSE23GYPFS (Refrigerators - Side-by-Side) Minimum opening depth = verified case-only depth 28.5 in + GE rear clearance 2 in.Open original source ↗ Why this value was usedMinimum opening depth = verified case-only depth 28.5 in + GE rear clearance 2 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2Open original source ↗ Why this value was usedExact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Secondary source only | GSE23GYPFS (Refrigerators - Side-by-Side) www.qualityelectronicsonline.com | Retained specification excerpt: Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary p | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceGSE23GYPFS (Refrigerators - Side-by-Side) Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value.Open original source ↗ Why this value was usedExact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Secondary source only | GSE23GYPFS (Refrigerators - Side-by-Side) www.qualityelectronicsonline.com | Retained specification excerpt: Exact-model cached page explicitly labels rear_clearance_in=2 in; 1 cached copy/copies; no contrary | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceGSE23GYPFS (Refrigerators - Side-by-Side) Exact-model cached page explicitly labels rear_clearance_in=2 in; 1 cached copy/copies; no contrary parsed value.Open original source ↗ Why this value was usedExact-model cached page explicitly labels rear_clearance_in=2 in; 1 cached copy/copies; no contrary parsed value. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 3.25 in | ✓ Secondary source only · Calculated/inferred | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit3.25 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: ceil_to_1/8((width_open_90 - max(case_width,width_closed)) / 2) Confidence label: medium. Primary evidenceGE GSE23GYPFS Quick Specs Exact-model GE width-open geometry: width with door(s) open 90 degrees 39.25 in; widest closed appliance width 32.75 in; two-door per-side half-excess rounded upward to 1/8 in = 3.25 in. Table: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2Open original source ↗ Why this value was usedExact-model GE width-open geometry: width with door(s) open 90 degrees 39.25 in; widest closed appliance width 32.75 in; two-door per-side half-excess rounded upward to 1/8 in = 3.25 in. Table: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2 Calculation or inference: ceil_to_1/8((width_open_90 - max(case_width,width_closed)) / 2). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.75 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit32.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Width (in.) H -> 32-3/4Open original source ↗ Why this value was usedWidth (in.) H -> 32-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.125 in | ✓ Secondary source only | GE GSE23GYPFS Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GSE23GYPFS Quick Specs Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2Open original source ↗ Why this value was usedVisually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69.875 in. Earlier retained values: 69.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visual/native table repair: replaced legacy misassociated value 69.625 with labeled GE table value 69.875.
View source scope, location, and impact on fitassets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: GSE23GYPFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: GSE23GYPFS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.qualityelectronicsonline.com · Web source · secondary model/source
Model numbers covered: GSE23GYPFS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.