Measurement evidence for GE GSE23GGPBB

Value used by ExactFit

32.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width (in.) H -> 32-3/4

Why this value was used

Width (in.) H -> 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of case (in.) C -> 69

Why this value was used

Height to top of case (in.) C -> 69

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Visual/native table repair: replaced legacy misassociated value 69.625 with labeled GE table value 69.875.

Why this value was used

Visual/native table repair: replaced legacy misassociated value 69.625 with labeled GE table value 69.875.

Other evidence found

• 69.625 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Height to top of door (in.) B -> 69-5/8. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth without door (in.) D -> 28-1/2

Why this value was used

Case depth without door (in.) D -> 28-1/2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth less door handle (in.) E -> 32-3/4

Why this value was used

Case depth less door handle (in.) E -> 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case depth with door handle (in.) F -> 34-3/4

Why this value was used

Case depth with door handle (in.) F -> 34-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

50.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with fresh food door open 90° (in.) G -> 50-1/2

Why this value was used

Depth with fresh food door open 90° (in.) G -> 50-1/2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

GE measurement source — 104319990.pdf + 104319990.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, si
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, side_ventilation_clearance_in=0.125; result=33 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, side_ventilation_clearance_in=0.125; result=33 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

GE measurement source — 104319990.pdf + 104319990.pdf
www.qualityelectronicsonline.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.875,
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.875, top_clearance_in=1; result=70.875 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.875, top_clearance_in=1; result=70.875 in. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

GE measurement source — 104319990.pdf + 104319990.pdf
www.qualityelectronicsonline.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=28.5
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=28.5, rear_clearance_in=2; result=30.5 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: depth_case_only_in=28.5, rear_clearance_in=2; result=30.5 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 104319990.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2

Why this value was used

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — 104319990.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2

Why this value was used

Exact-model cached GE ordered table; trailing Each side / Top / Back trio. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE specification record — 104319990.pdf
www.qualityelectronicsonline.com · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Visually reviewed exact-model GE Quick Specs ordered table. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2. Trailing labeled air-clearance trio: Each side=0.125, Top=1, Back=2 in.

Why this value was used

Visually reviewed exact-model GE Quick Specs ordered table. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2. Trailing labeled air-clearance trio: Each side=0.125, Top=1, Back=2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE specification record — 104319990.pdf
www.qualityelectronicsonline.com · Specification sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Visually reviewed exact-model GE Quick Specs ordered table. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2. Trailing labeled air-clearance trio: Each side=0.125, Top=1, Back=2 in.

Why this value was used

Visually reviewed exact-model GE Quick Specs ordered table. Values: 69-7/8 | 69-5/8 | 69 | 28-1/2 | 32-3/4 | 34-3/4 | 50-1/2 | 32-3/4 | 39-1/4 | 1/8 | 1 | 2. Trailing labeled air-clearance trio: Each side=0.125, Top=1, Back=2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.25 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: ceil_to_1/8((39.25 - 32.75) / 2)

Confidence label: high.

Primary evidence

GE measurement source — GSE23GGPBB_104319990.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE side-by-side Quick Specs visually prints 39.25 in open width and 32.75 in closed width. The GE side-by-side maximum per-side operating-envelope rule ceil_to_1/8((39.25 - 32.75) / 2) = 3.25 in is back-tested against GSS28/GZS24 sheets that directly print the separate freezer- and fresh-food-side 90-degree wall clearances.

Why this value was used

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model GE side-by-side Quick Specs visually prints 39.25 in open width and 32.75 in closed width. The GE side-by-side maximum per-side operating-envelope rule ceil_to_1/8((39.25 - 32.75) / 2) = 3.25 in is back-tested against GSS28/GZS24 sheets that directly print the separate freezer- and fresh-food-side 90-degree wall clearances. Calculation or inference: ceil_to_1/8((39.25 - 32.75) / 2).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE installation document — 104319990.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width (in.) H -> 32-3/4

Why this value was used

Width (in.) H -> 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.