This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Width (in.) H -> 35-3/4Open original source ↗ Why this value was usedWidth (in.) H -> 35-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 69 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit69 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Height to top of case (in.) C -> 69Open original source ↗ Why this value was usedHeight to top of case (in.) C -> 69 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Height to top of hinge (in.) B -> 69-7/8Open original source ↗ Why this value was usedHeight to top of hinge (in.) B -> 69-7/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.375 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit29.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Case depth without door (in.) D -> 29-3/8Open original source ↗ Why this value was usedCase depth without door (in.) D -> 29-3/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.75 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit34.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Case depth less door handle (in.) E -> 34-3/4Open original source ↗ Why this value was usedCase depth less door handle (in.) E -> 34-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 36.25 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit36.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Case depth with door handle (in.) F -> 36-1/4Open original source ↗ Why this value was usedCase depth with door handle (in.) F -> 36-1/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.375 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit48.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Depth with fresh food door open 90˚ (in.) G -> 48-3/8Open original source ↗ Why this value was usedDepth with fresh food door open 90˚ (in.) G -> 48-3/8 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Secondary source only · Calculated/inferred | GE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications assets.skulytics.io | Retained specification excerpt: Exact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall | |
Value used by ExactFit36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * exact/family installation side clearance Confidence label: medium. Calculation inputs: Overall width; Primary evidenceGE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Exact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall-clearance measurement.Open original source ↗ Why this value was usedExact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall-clearance measurement. Calculation or inference: width_doors_closed_in + 2 * exact/family installation side clearance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.875 in | ✓ Secondary source only · Calculated/inferred | GE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances GE | Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.875 in plus documented top clearan | |
Value used by ExactFit70.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceGE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances Minimum opening height derived from highest appliance endpoint 69.875 in plus documented top clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest appliance endpoint 69.875 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.375 in | ✓ Secondary source only · Calculated/inferred | GE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances GE | Retained specification excerpt: Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in. | |
Value used by ExactFit31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceGE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | Unknown | ? Not found | GE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Publisher not recorded | Retained specification excerpt: Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 16-3/8). Exact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall-clearance measurement. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | Unknown | ? Not found | GE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Publisher not recorded | Retained specification excerpt: Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 16-3/8). Exact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall-clearance measurement. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — exact model | GE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances GE | Retained specification excerpt: Top Air Clearances\",\"value\":\"1 in | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceGE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances Top Air Clearances\",\"value\":\"1 inOpen original source ↗ Why this value was usedTop Air Clearances\",\"value\":\"1 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — exact model | GE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances GE | Retained specification excerpt: Back Air Clearances\",\"value\":\"2 in | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceGE® ENERGY STAR® 27.7 Cu. Ft. French-Door Refrigerator - GFE28GMKES - GE Appliances Back Air Clearances\",\"value\":\"2 inOpen original source ↗ Why this value was usedBack Air Clearances\",\"value\":\"2 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 16.375 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit16.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Exact-model GE table: minimum distance between side of case and wall to allow doors to open fully = 16.375 in.Open original source ↗ Why this value was usedExact-model GE table: minimum distance between side of case and wall to allow doors to open fully = 16.375 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Secondary source only | GE GFE28GMKES Quick Specs assets.skulytics.io | Page 1 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceGE GFE28GMKES Quick Specs Width (in.) H -> 35-3/4Open original source ↗ Why this value was usedWidth (in.) H -> 35-3/4 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | Unknown | ? Not found | GE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Publisher not recorded | Retained specification excerpt: Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceGE measurement source — GE exact-family installation manuals and cached exact-model side-air specifications Corrected prior value 16.375 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 16-3/8). Exact-family installation opening is 36 in with 1/8 in side air clearance. Replaces a door-open wall-clearance measurement. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedThe retained record does not establish source scope or a resolvable supporting source. Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: Unknown. Earlier retained values: 16.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
The retained record does not establish source scope or a resolvable supporting source.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: GE exact-family installation manuals and cached exact-model side-air specifications. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: GE exact-family installation manuals and cached exact-model side-air specifications. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: GE exact-family installation manuals and cached exact-model side-air specifications. No rejected related-model candidate is identified in the retained record.
The retained record does not establish source scope or a resolvable supporting source.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Quick Specs · secondary model/source
Model numbers covered: GFE28GMKES. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Hinge-side wall clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL unavailable in the record.
GE · Web source · exact model/source
Model numbers covered: GFE28GMKES. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
4 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.