This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Column Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-09. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.875 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Width of Cabinet 32 7/8"Open original source ↗ Why this value was usedWidth of Cabinet 32 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.5 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Height Without Hinge 71 1/2"Open original source ↗ Why this value was usedHeight Without Hinge 71 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72.5 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Height With Hinge 72 1/2"Open original source ↗ Why this value was usedHeight With Hinge 72 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.625 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire Professional measurement source — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared-chassis propagation: Shared 19-cu-ft single-door chassis inference from GRDA1911AF: identical width, heights, door depth, open depth, and product weight; cabinet-only depth 24.625 in. Confidence label: medium. Primary evidenceFrigidaire Professional measurement source — 106160758.pdf Shared 19-cu-ft single-door chassis inference from GRDA1911AF: identical width, heights, door depth, open depth, and product weight; cabinet-only depth 24.625 in.Open original source ↗ Why this value was usedShared 19-cu-ft single-door chassis inference from GRDA1911AF: identical width, heights, door depth, open depth, and product weight; cabinet-only depth 24.625 in. Calculation or inference: shared-chassis propagation: Shared 19-cu-ft single-door chassis inference from GRDA1911AF: identical width, heights, door depth, open depth, and product weight; cabinet-only depth 24.625 in.. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 27 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit27 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Depth With Door 27"Open original source ↗ Why this value was usedDepth With Door 27" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27 in | ✓ Verified — retained secondary source | Frigidaire Professional measurement source — appliances-refrigerators-top-freezer-refrigerators-18-6-cu-ft-single-door-refrigerator www.brandsmartusa.com | Retained specification excerpt: Exact-model retailer specification: Depth Including Handles 27 in; consistent with manufacturer-publ | |
Value used by ExactFit27 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceFrigidaire Professional measurement source — appliances-refrigerators-top-freezer-refrigerators-18-6-cu-ft-single-door-refrigerator Exact-model retailer specification: Depth Including Handles 27 in; consistent with manufacturer-published Depth With Door 27 in.Open original source ↗ Why this value was usedExact-model retailer specification: Depth Including Handles 27 in; consistent with manufacturer-published Depth With Door 27 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.25 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit58.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Depth With Door 90° Open 58 1/4"Open original source ↗ Why this value was usedDepth With Door 90° Open 58 1/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33 in | ✓ Conflicting sources — resolved | Frigidaire Professional measurement source — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional measurement source — 90280479.pdf Manufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 33 in width.Open original source ↗ Why this value was usedManufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 33 in width. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 73.5 in | ✓ Verified — retained secondary source | Frigidaire Professional measurement source — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit73.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional measurement source — 90280479.pdf Manufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 73.5 in height.Open original source ↗ Why this value was usedManufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 73.5 in height. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25.625 in | ✓ Verified — retained secondary source | Frigidaire Professional measurement source — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit25.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional measurement source — 90280479.pdf Manufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 25.625 in minimum depth.Open original source ↗ Why this value was usedManufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 25.625 in minimum depth. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280479.pdf Exact PRDA1922AF manual: installation clearances — Sides 3/16", Top & Back 1".Open original source ↗ Why this value was usedExact PRDA1922AF manual: installation clearances — Sides 3/16", Top & Back 1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280479.pdf Exact PRDA1922AF manual: installation clearances — Sides 3/16", Top & Back 1".Open original source ↗ Why this value was usedExact PRDA1922AF manual: installation clearances — Sides 3/16", Top & Back 1". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280479.pdf r ap pliance. Sufficient air circulation is essen tial to operate your appliance properly. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential type environments WARNING Installation clearances Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 3/16" Top & Back 1" 33" 73.5" 25.625" min Minimum Cabinet dimensions for Single Unit WITHOUT Trim KitOpen original source ↗ Why this value was usedr ap pliance. Sufficient air circulation is essen tial to operate your appliance properly. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential type environments WARNING Installation clearances Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 3/16" Top & Back 1" 33" 73.5" 25.625" min Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280479.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280479.pdf r ap pliance. Sufficient air circulation is essen tial to operate your appliance properly. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential type environments WARNING Installation clearances Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 3/16" Top & Back 1" 33" 73.5" 25.625" min Minimum Cabinet dimensions for Single Unit WITHOUT Trim KitOpen original source ↗ Why this value was usedr ap pliance. Sufficient air circulation is essen tial to operate your appliance properly. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential type environments WARNING Installation clearances Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 3/16" Top & Back 1" 33" 73.5" 25.625" min Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.875 in | ✓ Verified — retained secondary source | Frigidaire Professional installation document — 90280478.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Professional installation document — 90280478.pdf Width of Cabinet 32 7/8"Open original source ↗ Why this value was usedWidth of Cabinet 32 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 33 in. Earlier retained values: 35.1 in, 35.01 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Manufacturer manual: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, 33 in width.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: PRDA1922AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
6 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: PRDA1922AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.brandsmartusa.com · Web source · secondary model/source
Model numbers covered: PRDA1922AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with handle.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: PRDA1922AF. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.