Measurement evidence for Frigidaire Gallery GRTE2055AF

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 30"

Why this value was used

Width 30"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height Without Hinge 65 7/8"

Why this value was used

Height Without Hinge 65 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 66 3/8"

Why this value was used

Height With Hinge 66 3/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 28 1/4"

Why this value was used

Depth of Cabinet 28 1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 32"

Why this value was used

Depth With Door 32"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 32"

Why this value was used

Depth With Door and Handle 32"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

58.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 58 5/8"

Why this value was used

Depth With Door 90° Open 58 5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-09

Frigidaire Gallery installation-envelope calculation: case_width_in=30, side_ventilation_clearance_in=0.375; result=30.75 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m

Why this value was used

Frigidaire Gallery installation-envelope calculation: case_width_in=30, side_ventilation_clearance_in=0.375; result=30.75 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-09

Frigidaire Gallery installation-envelope calculation: height_hinge_in=66.375, top_clearance_in=0.375; result=66.75 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m

Why this value was used

Frigidaire Gallery installation-envelope calculation: height_hinge_in=66.375, top_clearance_in=0.375; result=66.75 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-09

Frigidaire Gallery installation-envelope calculation: depth_case_only_in=28.25, rear_clearance_in=1; result=29.25 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m

Why this value was used

Frigidaire Gallery installation-envelope calculation: depth_case_only_in=28.25, rear_clearance_in=1; result=29.25 in. Product source: 103503127.pdf. Clearance source text: NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Sides and top 3/8" (9.5 mm)

Why this value was used

Sides and top 3/8" (9.5 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Sides and top 3/8" (9.5 mm)

Why this value was used

Sides and top 3/8" (9.5 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery measurement source — 103503128.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Sides and top 3/8" (9.5 mm)

Why this value was used

Sides and top 3/8" (9.5 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503128.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-09

NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m

Why this value was used

NOTE Do not block the lower front of the appliance. Sufficient air circulation is essential for the proper operation of the appliance. WARNING! Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at the front and rear. • The sides should tilt 1/4" (6 mm) from front to back to ensure that doors close and seal properly. • Align the doors with each other and level them. 3.7 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side clockwise until they contact the floor. Do not raise the cabinet. NOTE The anti-tip bracket must be installed according to the instructions in the User Manual. Failure to do so m

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery installation document — 103503127.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 30"

Why this value was used

Width of Cabinet 30"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.