Measurement evidence for Frigidaire Gallery GRSN2620AF
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-09. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Frigidaire Gallery measurement source — 103502813.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: case_width_in=35.875, side_ventilation_clearance_in=0.375; result=36.625 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
Frigidaire Gallery installation-envelope calculation: case_width_in=35.875, side_ventilation_clearance_in=0.375; result=36.625 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Other evidence found
36.875 in — superseded
Document 103502814.pdf + Document 103502813.pdf; page 7. Model scope: not separately recorded. Raw value: Derived minimum opening from validated overall width 36.125 in and exact-model side clearance 0.375 in per side. Side evidence: Sides & Top | 3/8" | Back. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire Gallery measurement source — 103502813.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: height_hinge_in=69.875, top_clearance_in=0.375; result=70.25 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
Frigidaire Gallery installation-envelope calculation: height_hinge_in=69.875, top_clearance_in=0.375; result=70.25 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker Calculation or inference: height_hinge_in + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire Gallery measurement source — 103502813.pdf www.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: depth_case_only_in=28.75, rear_clearance_in=1; result=29.75 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
Frigidaire Gallery installation-envelope calculation: depth_case_only_in=28.75, rear_clearance_in=1; result=29.75 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery measurement source — 103502813.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery measurement source — 103502813.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502813.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09
7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502813.pdf www.ajmadison.com · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09
7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502814.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 36.625 in. Earlier retained values: 36.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Frigidaire Gallery installation-envelope calculation: case_width_in=35.875, side_ventilation_clearance_in=0.375; result=36.625 in. Product source: 103502814.pdf. Clearance source text: 7 INSTALLATION NOTE If your unit is placed with the door hinge side against a wall, you may have to allow additional space for the handle so the door can be opened wider. This Use & Care Manual provides general operating instructions for your model. Use the unit only as instructed in this Use & Care Manual. Before starting the appli ance, follow these important first steps. Installation Installation clearances • Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top ⅜" Back 1" Location • Choose a place that is near a ground ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. • Consider water supply availability for models equipped with an automat ic ice maker. If you do not hook up water to the appliance, remember to turn the ice maker Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Model numbers covered: GRSN2620AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
